GE PGS960BELTS LP Conversion Kit - Page 2

Additional Information, Adjusting Air Shutter Settings, For Oven Burners, Adjusting Low Flame - lowes

Page 2 highlights

CONVERTING THE OVEN BURNERS NOTICE: This product cannot be converted to propane by adjusting WKHRYHQRUL¿FHV7KHRUL¿FHVPXVWEHUHSODFHGIRUSURSDQH UPPER AND LOWER OVEN BAKE BURNER ORIFICES 1. Remove the lower oven door from the unit  5 HPRYHRYHQUDFNVRYHQERWWRPVDQGÀDPHVSUHDGHUV from both ovens. In the lower oven, remove the enclosure around the rear of the bake burner held in place by three 3KLOOLSVVFUHZV 3. Remove all 1/4" hex screws securing the bake burners. Gently slide each bake burner to the left to remove it from the RUL¿FHDQGDOORZEXUQHUV to rest on the bottom of their respective ovens.  : LWKD´ZUHQFKORRVHQHDFKRUL¿FHE\WXUQLQJFRXQWHU clockwise and remove. NOTICE: 6DYHWKHVHRUL¿FHVIRUIXWXUHFRQYHUVLRQEDFNWRQDWXUDOJDV  6 HOHFWWKHDSSURSULDWHEDNHRUL¿FHIRUHDFKRYHQIURPWKH NLWDQGLQVWDOORQWKHWKUHDGHG¿WWLQJV7LJKWHQZLWKZUHQFK until snug.  * HQWO\UHSODFHWKHEDNHEXUQHUVRYHUWKHLUUHVSHFWLYHRUL¿FHV and replace all 1/4" hex screws securing the burners. BROIL BURNER ORIFICE 1. Remove the 1/4" hex screw securing the broil burner and allow it to hang down free of the EURLORUL¿FH Broil 2UL¿FH 2. Apply a 1/2" wrench to the hex base of the RUL¿FH/RRVHQWKH RUL¿FHE\WXUQLQJFRXQWHUFORFNZLVHDQGUHPRYH Oven Light NOTICE: 6DYHWKHVHRUL¿FHVIRUIXWXUHFRQYHUVLRQEDFNWRQDWXUDOJDV  6 HOHFWWKHSURSDQHEURLORUL¿FHIURPWKHNLWDQGLQVWDOOLWRQ the broil elbow. Tighten until snug.  5 HSODFHWKHEURLOEXUQHURYHUWKHRUL¿FHDQGUHSODFHWKH screw securing the burner. ADJUSTING AIR SHUTTER SETTINGS FOR OVEN BURNERS The air shutters should be turned to the marked settings NG or propane or set according to the following table. BURNER AIR SHUTTER AIR SHUTTER SETTING FOR PROPANE SETTING FOR NG Lower Oven Broil Burner 0.690 0.690 Upper Oven Bake Burner 0.750 0.750 Lower Oven Bake Burner Full Open Full Open 3KLOOLSV6FUHZ Air shutter Air Shutter Setting :LWKD3KLOOLSVKHDGVFUHZGULYHUORRVHQWKHVFUHZVVHFXULQJ the air shutters on the burners and adjust the air shutters according to chart. %DNHDQGEURLOÀDPHVPXVWEHFKHFNHGZLWKWKHRYHQ GRRUVFORVHGWRSURSHUO\FKHFNÀDPHFKDUDFWHULVWLFV 1. Turn on the gas. 2. Turn on the electricity. 3. Reinstall the lower oven door. Close both doors. 4. Turn on both bake burners. 5. For each burner, observe the following through the oven door windows.  D,IWKHÀDPHVDUH\HOORZRSHQWKHDLUVKXWWHUPRUH  E,IWKHÀDPHVEORZDZD\RUÀXWWHUIURPWKHEXUQHUFORVH the air shutter slightly, but not by more than 1/8". 6. Turn bake burner off and repeat with broil burner. WARNING If you attempt to measure the inner cone RIWKHÀDPHSOHDVHXVHFDXWLRQEXUQVFRXOGUHVXOW 2YHQEXUQHUÀDPHPXVWEHREVHUYHGZLWKWKHGRRUFORVHG WRSURSHUO\FKHFNÀDPHFKDUDFWHULVWLFV  &KHFNLQJWKHÀDPHVL]H It should be approximately 1/2" to 3/4" long for the bake and broil burners. The combustion quality of WKHEXUQHUÀDPHVQHHGVWR be determined visually. 127(,IEXUQHUÀDPHVORRNOLNH $ IXUWKHUDLUVKXWWHU adjustment to the bake buner is required. Normal EXUQHUÀDPHVVKRXOGORRNOLNH % RU & GHSHQGLQJ on the type of gas you use. With propane gas, some yellow tipping on the outer cones is normal. (A) Yellow flames: Further Adjustment Required (B) Yellow tips on outer cones: Normal for Propane Gas (C) Soft blue flames: Normal for Natural Gas )RUHLJQSDUWLFOHVLQWKHJDVOLQHPD\FDXVHDQRUDQJHÀDPHDW ¿UVWEXWWKLVZLOOVRRQGLVDSSHDU 8. Retighten the air shutter screws. 9. When all adjustments are made and the results are satisfactory: a. Replace the enclosure around the rear of the bake burner in the lower oven.  E5HSODFHWKHÀDPHVSUHDGHUV c. Replace the oven bottoms and oven racks. ADJUSTING LOW FLAME SETTING ON COOKTOP BURNERS Low setting adjustments must be made with other burners in operation on a medium setting. This procedure prevents the ORZÀDPHIURPEHLQJVHWWRRORZUHVXOWLQJLQWKHÀDPHEHLQJ extinguished when other burners are turned on. A. Turn on all surface burners to medium setting. % 7XUQWKHNQRERQWKHEXUQHUEHLQJDGMXVWHGWR³/2´ & 5HPRYHWKHNQREDQGLQVHUWDVPDOOÀDWEODGHVFUHZGULYHU into the valve shaft and/or side adjustment screw(s) as shown and turn clockwise to fully tighten down the bypass screw(s). Repeat for all valves. ' ,IÀDPHDSSHDUVWRRORZRUXQVWDEOHVORZO\WXUQE\SDVVVFUHZ FRXQWHUFORFNZLVHXQWLODVWDEOHÀDPHH[LVWVIRUHDFKEXUQHU Remember, other burners must be turned on to medium. SPECIALTY BURNERS Dual Oval Burner - This burner should be properly adjusted with both bypass screws completely screwed in. Multi-Ring Burner±7KHRXWHUULQJRIÀDPHVVKRXOGEH DGMXVWHGZLWKWKHNQREDWWKH0(' Burner Cap by adjusting the set screw in the Flames FHQWHUYDOYHVKDIW7KHÀDPHVVKRXOG be adjusted so that they barely curl over the top edge of the burner cap. 7KHFHQWHUULQJRIÀDPHVVKRXOGEH adjusted with the knob at the LO setting by adjusting the set screw to the right of the valve shaft. ( $GGLWLRQDOO\IRUHDFKEXUQHUEHLQJDGMXVWHGTXLFNO\RSHQ DQGFORVHWKHRYHQGRRUZKLOHREVHUYLQJÀDPH,IÀDPHLV extinguished, continue adjusting bypass screw for a larger ÀDPH5HSHDWGRRURSHQLQJVXQWLOÀDPHLVVWDEOH F. Replace the knob. Adjustment screw for outer ring Adjustment screw for center ring Adjustment screw for center ring Adjustment screw for 2 oval rings Adjustment screws for multi-ring burner only Adjustment screws for dual oval burner only Center adjustment screw only for all other burners. SPECIAL NOTE: To convert the oven back to natural gas, reverse the instructions given in making propane adjustments. NOTICE: 2QFHWKHFRQYHUVLRQLVFRPSOHWHDQGFRQ¿UPHG¿OORXW WKHSURSDQHVWLFNHUDQGLQFOXGH\RXUQDPHRUJDQL]DWLRQ and date conversion was made. Apply the sticker to the range near the regulator to alert others in the future that this appliance has been converted to propane. If converting back to natural gas from propane, please remove the sticker so others know the appliance is set to use natural gas. ADDITIONAL INFORMATION BURNER OUTPUT RATINGS: BTU/HR NG (Natural) Gas 5" W.C.P. BURNER LF LF1 LF2 LF3 LFC LR RF RR C C1 C2 Upper Bake Broil Lower Bake BTU RATE 21,000 N/A N/A N/A N/A 5,000 15,000 9,500 8,000 9,500 6,800 7,000 16,500 14,000 ORIFICE SIZE (mm) 0.045 0.045 0.045 0.025 0.040 0.070 0.0555 0.0555 0.047 0.046 0.071 0.066 COLOR None None None None :KLWH3XUSOH Brown Yellow Yellow none Yellow Black/Blue Red MARKING 114N 114N 114N 63N 101N 178N 141N 141N 119N 046N 071N 066N 198 N III Denotes 1.98mm Orifice size opening Denotes Natural Gas PROPANE CONVERSION INSTRUCTIONS 31-11088 05-17 GEA PGS960

  • 1
  • 2

Low setting adjustments must be made with other burners in
operation on a medium setting. This procedure prevents the
extinguished when other burners are turned on.
A. Turn on all surface burners to medium setting.
into the valve shaft and/or side adjustment screw(s) as
shown and turn clockwise to fully tighten down the bypass
screw(s). Repeat for all valves.
Remember, other burners must be turned on to medium.
SPECIALTY BURNERS
Dual Oval Burner
– This burner should be properly adjusted
with both bypass screws completely screwed in.
Multi-Ring Burner
by adjusting the set screw in the
be adjusted so that they barely curl
over the top edge of the burner cap.
adjusted with the knob at the LO
setting by adjusting the set screw to
the right of the valve shaft.
extinguished, continue adjusting bypass screw for a larger
F.
Replace the knob.
ADDITIONAL INFORMATION
ADJUSTING AIR SHUTTER SETTINGS
FOR OVEN BURNERS
ADJUSTING LOW FLAME SETTING
ON COOKTOP BURNERS
It should be approximately
1/2” to 3/4” long for the bake
and broil burners.
The combustion quality of
be determined visually.
SPECIAL NOTE:
To convert the oven back to natural gas, reverse the
instructions given in making propane adjustments.
PROPANE CONVERSION INSTRUCTIONS
31-11088
05-17
GEA
PGS960
NOTICE:
and date conversion was made. Apply the sticker to the
range near the regulator to alert others in the future that
this appliance has been converted to propane. If converting
back to natural gas from propane, please remove the sticker
so others know the appliance is set to use natural gas.
BURNER OUTPUT RATINGS: BTU/HR
NG (Natural) Gas 5” W.C.P.
BURNER
BTU
RATE
ORIFICE
SIZE (mm)
COLOR
MARKING
LF
21,000
LF1
N/A
0.045
None
114N
LF2
N/A
0.045
None
114N
LF3
N/A
0.045
None
114N
LFC
N/A
0.025
None
63N
LR
5,000
0.040
101N
RF
15,000
0.070
Brown
178N
RR
9,500
0.0555
Yellow
141N
C
8,000
C1
9,500
0.0555
Yellow
141N
C2
6,800
0.047
none
119N
Upper Bake
7,000
0.046
Yellow
046N
Broil
16,500
0.071
Black/Blue
071N
Lower Bake
14,000
0.066
Red
066N
The air shutters should be turned to the marked settings NG or
propane or set according to the following table.
the air shutters on the burners and adjust the air shutters
according to chart.
1.
Turn on the gas.
2.
Turn on the electricity.
3.
Reinstall the lower oven door. Close both doors.
4.
Turn on both bake burners.
5.
For each burner, observe the following through the oven
door windows.
the air shutter slightly, but not by more than 1/8”.
6.
Turn bake burner off and repeat with broil burner.
BURNER
AIR SHUTTER
SETTING FOR PROPANE
AIR SHUTTER
SETTING FOR NG
Lower Oven
Broil
Burner
0.690
0.690
Upper Oven
Bake
Burner
0.750
0.750
Lower Oven
Bake
Burner
Full Open
Full Open
Air Shutter
Setting
Air shutter
WARNING
If you attempt to measure the inner cone
Center adjustment screw only for all other burners.
Adjustment screws for
multi-ring burner only
Adjustment screws for
dual oval burner only
Adjustment screw
for outer ring
Adjustment screw
for center ring
Adjustment
screw for
center ring
Adjustment
screw for
2 oval rings
Flames
Burner Cap
198
III
Denotes 1.98mm Orifice size opening
Denotes Natural Gas
N
CONVERTING THE OVEN BURNERS
UPPER AND LOWER OVEN BAKE BURNER
ORIFICES
1.
Remove the lower oven door from the unit
from both ovens.
In the lower oven, remove the enclosure
around the rear of the bake burner held in place by three
3.
Remove all 1/4” hex
screws securing the bake
burners. Gently slide
each bake burner to the
left to remove it from the
to rest on the bottom of
their respective ovens.
clockwise and remove.
until snug.
and replace all 1/4” hex screws securing the burners.
BROIL BURNER ORIFICE
1.
Remove the 1/4” hex
screw securing the broil
burner and allow it to
hang down free of the
2.
Apply a 1/2” wrench
to the hex base of the
the broil elbow. Tighten until snug.
screw securing the burner.
NOTICE:
This product cannot be converted to propane by adjusting
adjustment to the bake buner is required. Normal
on the type of gas you use. With propane gas, some
yellow tipping on the outer cones is normal.
8.
Retighten the air shutter screws.
9.
When all adjustments are made and the results are
satisfactory:
a.
Replace the enclosure around the rear of the bake
burner in the lower oven.
c. Replace the oven bottoms and oven racks.
(A) Yellow flames:
Further Adjustment
Required
(B) Yellow tips on
outer cones:
Normal for Propane Gas
(C) Soft blue flames:
Normal for Natural Gas
NOTICE:
Broil
Oven
Light
NOTICE: