GE PHP9036SJSS Quick Specs - Page 1

GE PHP9036SJSS Manual

Page 1 highlights

PHP9036SJ GE Profile™ Series 36" Built-In Touch Control Induction Cooktop Dimensions and Installation Information (in inches) PHP9036SJ Important: Requires a 5" free area between the bottom of the cooktop to any combustible material, i.e., shelving. Free area not required when installing wall oven underneath cooktop. Refer to installation instructions. Requires a 15" minimum from cooktop to adjacent overhead cabinets. Units are furnished with a 48" flexible armored cable. Note: 36" induction cooktops are approved for use over select GE 30" Single Wall Ovens and Warming Drawers. Refer to cooktop and wall oven/warming drawer installation instructions packed with product for current dimensional data. If installed with a GE Telescopic Downdraft System, consult both the cooktop and downdraft installation instructions packed with product before installing. Cooktop gas/electric supply may need to be re-routed to install downdraft. The countertop cutout requires 23-1/2" minimum flat countertop surface and 25" minimum total countertop depth. In addition, other clearances to front edge of the countertop must be considered. Before installing, consult installation instructions packed with product for ­ current dimensional data. Approximate Cooking Dimensions 13" MAX. depth of unprotected overhead cabinets (when no hood or microwave is installed) 4-5/8" at baffle near center of vunit (except when installed above an approved wall oven) and 3-1/4" at rear of air intake 36-1/8" Cooktop 20-1/2" 1-3/4" MIN. to rear wall 18-7/8" 33-3/4" 19-1/8" to 19-1/4" 33-7/8" to 34" 2-1/2" MIN. Required To insure accuracy, it is best to make a template when cutting the opening in the counter 30" MIN. from countertop to unprotected cabinet (when no hood or microwave is installed) See label next to nameplate for MIN. clearance to wall Electrical junction box 16" MIN. below countertop 2" MIN. clearance to side wall from cut-out on both sides of cooktop KW Rating 240V 11.1 208V 9.6 Amperage 240V 46.3 Amps† †Note: Check local codes 208V 46.3 Amps† for required breaker size For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000. 15" MIN. height from countertop to nearest cabinet (including light rails) on both sides of cooktop Listed by Underwriters Laboratories Specification Created 1/15

  • 1
  • 2

Specification Created 1/15
For answers to your Monogram,
®
GE Profile
or GE
®
appliance questions, visit our website
at geappliances.com or call GE Answer Center
®
service, 800.626.2000.
Listed by
Underwriters
Laboratories
To insure accuracy, it is best to make a
template when cutting the opening in the counter
Electrical junction box 16" MIN.
below countertop
Cooktop
36-1/8"
20-1/2"
18-7/8"
33-3/4"
19-1/8" to
19-1/4"
33-7/8"
to 34"
2-1/2" MIN.
Required
1-3/4" MIN.
to rear wall
4-5/8" at baffle near center
of vunit (except when installed
above an approved wall
oven) and 3-1/4" at rear
of air intake
overhead cabinets (when no
hood or microwave is installed)
30" MIN. from countertop to
unprotected cabinet (when
no hood or microwave is
installed)
2" MIN. clearance
to side wall from cut-out
on both sides of cooktop
15" MIN. height from countertop
to nearest cabinet (including
light rails) on both sides of
cooktop
See label next
to nameplate for
MIN. clearance
to wall
IMPORTANT:
Requires a 5" free area between
the bottom of the cooktop to any combustible
material, i.e., shelving. Free area not required
when installing wall oven underneath cooktop.
Refer to installation instructions. Requires
a 15" minimum from cooktop to adjacent
overhead cabinets. Units are furnished with a
48" flexible armored cable.
NOTE:
36" induction cooktops are approved
for use over select GE 30" Single Wall Ovens
and Warming Drawers. Refer to cooktop
and wall oven/warming drawer installation
instructions packed with product for current
dimensional data. If installed with a GE
Telescopic Downdraft System, consult both the
cooktop and downdraft installation instructions
packed with product before installing. Cooktop
gas/electric supply may need to be re-routed
to install downdraft. The countertop cutout
requires 23-1/2" minimum flat countertop
surface and 25" minimum total countertop
depth. In addition, other clearances to front
edge of the countertop must be considered.
Before installing, consult installation
instructions packed with product for
current dimensional data.
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
PHP9036SJ
GE Profile
Series 36" Built-In Touch Control Induction Cooktop
KW Rating
240V
11.1
208V
9.6
Amperage
240V
46.3 Amps
208V
46.3 Amps
NOTE:
Check local codes
for required breaker size
APPROXIMATE COOKING DIMENSIONS