GE PSB1200NBB Quick Specs - Page 2
GE Profile Advantium, Volt - 30 Wall Oven
UPC - 084691188773
View all GE PSB1200NBB manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
PSB1200NBB/WW GE Profile Advantium® 120 Volt - 30" Wall Oven Preparation with an Accessory Drawer Prepare the opening The Advantium PSB1200/1 series can be installed in combination with other GE/Monogram appliances. Always follow each product's Installation Instructions to compete the installation. Single Oven Installation: Order a 30" wide single oven cabinet or cut the opening in a wall to the dimensions shown. 30" * For existing cutouts, a maximum width 23-1/2" of 28-1/2" is acceptable. If the opening is slightly wider, secure a furring strip on each side of the cutout for securing 25-1/4" Min. the oven. • Allow 3/4" to 2-1/8" case trim overlap 21" on the sides and 7/8" overlap on the bottom of the opening for all models. The amount of overlap on the sides depends on the actual cutout width. Allow 1-1/4" case trim overlap on the top for models PSB1200 and PSB1201 5" min. from floor 1" min. above toekick Construct Base Min. 3/8" Plywood Supported by 2x4 or 2x2 Runners all Four Sides and for models ZSC1201 and ZSC1202. • Oven overlaps will conceal cut edges on all sides of the opening. Note: PSB1200/1 series Advantium can be installed below GE/GE Profile non-downdraft gas and electric cooktops. It CANNOT be installed below induction or Monogram (2GU3841385) gas cooktops. Note: PSB1200/1 series Advantium oven comes with two lower trim pieces. One is for use above 36-inch height installations and one is for use below 36-inch installations. Use of the accessory drawer will replace the bottom trim piece for applicable installations. Please see installation instructions for full details. For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000. Prepare the opening (cont.) When installed over a single oven or a warming drawer, allow at least 2" between the two openings. This separation will provide clearance for bottom overlap of the Advantium and the other appliance overlaps. Construct a solid oven floor of 3/8" min. thick plywood supported by 2 x 4 or 2 x 2 runners on all sides. • the support must be level and rigidly mounted, flush with the bottom edge of the cutout. Installation over a GE/Monogram Warming Drawer: 30" 23-1/2" Construct Solid Bottom Min. 3/8" Plywood Supported 25-1/4" by 2x4 or 2x2 Min. Runners all Four Sides 21" 2" Min. (3" recommended) 5" min. from floor 1" min. above toekick Per warming drawer requirement Note: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details. Installation over a GE/Monogram Oven and Warming Drawer: Warming Drawer: 30" 23-1/2" 25-1/4" Min. Construct Solid Bottom Min. 3/8" Plywood Supported by 2x4 or 2x2 Runners all Four Sides 21" 2" Min. (3" recommended) 5" min. from floor 1" min. above toekick Per Oven Requirement 2" Min. Per warming drawer requirement Note: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details. Caution: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this approximate 80-pound oven and 30pound drawer, plus additional oven loads of up to 50 pounds or a total weight of 160 pounds. Listed by Underwriters Laboratories Specification Created 11/08 240445