GE PSB9120DFBB Quick Specs - Page 1

CL PSB9120DF 2x4's or equivalent solid floor 29-3/4" 30" Supported by 2 x 4 or 1 x 2 Runners, all Four Sides. (Must Support Advanf5lto"iomur im1n".fmrWoimn.a1l5l0Olbvs.e) n Dimensions (in inches)and CabinabeotveIntosetkaiclklation (in inches) GE Profile™ Series Advantium® 120V - 30 in. Wall Oven Suitable bracing Advanttoiursuumnpnpeowrrst all 21-5/8" oveovneor/f GcceaEnbtinePerltirnoe file™ Series A= Allow 1" overlap of oven over bottom edge of cutout, and allow 1-1/4" overlap at top edge of cutout. cooBk=iAnlglowto11w/1e6"r-3/4" for overlap of oven over side edges of cutout. dimensions and(Mcuasbt siunpepotrti1n3s0tlbasl.l)ation information (in inches) Note: Cabinets installed adjacent Cabinet width 4-3/16" Note: Cabinets installed adjacent to wall ovens must have an adhesion spec of at least 194° F temperature rating. 25-1/8" Cutout width 23-1/2" Cutout depth 4-3/16" to wall ovens must have an adhesion spec of at least a 194°F temperature rating. Note: 2" minimum between cutouts 19-1/8" 29-3/4" A B 21-1/2" To back of Control Junction box location 21-1/2" Back of Control 2-1/2" MIN between cutouts recommended-2" MIN required 19-1/8" Junction AAdvanBtium Wall box location Oven Dimensions (in i Conduit (48-1/2" long) Cabinet17I-n1s/2t"allation Cutout height (in inches) Construct Solid Bottom Min. 3/8" Plywood when installed above warming drawer or single wall oven. Conduit (46" long) A B CL Construct Solid Bottom 2x4's or MIN 3/8" Plywood Supporteedqbuyivalent 2 x 4 or 1 x 2 Runners, all FsooulridSidfleoso. r (Must Support 150 lbs. for Advantium) (Must Support 200 lbs. for Wall Oven) 29-3/4" Supported by 2 x 4 or 1 x 2 Runners, all Four Sides. Note: Cabinets installed adjacent(Must Support to wall ovens must ha5v"emain.afrdohmes1io5n0 lbs.) Installation Information: 9-1/4" cutout height 28-1/2" cutout width spec of at least 194°flFooterm1p" emraintu. re rating. 30" above toekick 25-1/8" Cutout width Before installing, consult installation instructions packed with product for ­current dimensional data. Suitable bracing to support runners 2" MIN between cutouts 21-5/8" over centerline of1c" aMbini.naebotve toekick or adjust (Must suptopoovertn 1in3st0allalbtiosn.)height 21-1/2" A= Allow 1" overlap of oven over bottom edgBeacokf ocfuCtoountt,roalnd allow 1-1/4" overlap at top edge of cutout. B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout. A Conduit Note: Advantium wallovens can be installed below GE/GE Profile Series nondowndraft gas and electric cooktops. It CANNOT be installed below induction or Cabinet width 4-3/16" 19-1/8" (48-1/2" long) Monogram (2GU3841385) gas cooktops. Note: Advantium wall oven comes with two lower trim pieces. One is for use above 36-inch height installations and one is for use below 36-inch installations. Use of the accessory drawer will replace the bottom trim piece for applicable installations. A B CL 2x4's or Junction box loceaqtiounivalent solid floor 29-3/4" Please see installation instructions for full details. 19-1/8" 21-1/2" To back of Control 2-1/2" MIN between cutouts recommended-2" MIN required 30" 29-3/4" For answers to your Monogram® or GE® appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000. Suitable bracing to s(4Cu6op"npldoounigrt)t runners A B Construct Solid Bottom A= Allow 21-5/8" MIN 3/8" Plywood Supported by 1-1/4" over of centerli2nex 4 or 1 x 2 Runners, cabinet(Must Support 150 lbs. all for Four SidBes=. Advantium) Allow o1v"eorlvaeprLULliansaabtdoeetprdrawtbtoooryirtipfeerssoevdegneoovfec 11/16"-3/4" for overlap (Must support 13(0MulbstsS.)upport 200 lbs. for Wall Oven) Specification Revised 7/13 240407 9-1/4" cutout heightCabinet width 4-3/16" 28-1/2" cutout width 2" MIN between cutouts