GE SCA1001KSS Installation Instructions - Page 13

Preparation of Top Cabinet, Checking for Proper DamperOperation, Mount the Oven - mounting plate

Get GE SCA1001KSS - Profile Advantium 120 Above-the-Cooktop Oven PDF manuals and user guides
UPC - 084691125570
View all GE SCA1001KSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Installation Instructions A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. A4. MOUNT THE OVEN • Read the instructions on the TOP CABINET TEMPLATE. • Tape it underneath the top cabinet. • Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. A3. ASSEMBLE AND INSTALL ADAPTOR Damper Exhaust Adaptor Blower Plate Back of Oven FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf. IMPORTANT: If filler blocks are not used, case damage may occur from over tightening screws. NOTE: When mounting the oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1-3. Do not pinch cord or lift oven by pulling cord. 1 Lift oven, tilt it forward, and hook slots at back bottom edge onto two lower tabs of mounting plate. 1 Place the oven in its upright position, with the top of the unit facing up. 2 Insert the tabs on each side of the damper into the holes at the inside rear of the adaptor. 3 Attach the exhaust adaptor to the blower plate with the two bronze metal screws provided. Make sure that the damper pivots easily before mounting oven. You will need to make adjustments to assure proper alignment with your house exhaust duct after the oven is installed. 2 Rotate front of oven up against cabinet bottom. 3 Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
13
3
2
Rotate front of oven
up against cabinet
bottom.
1
MOUNT THE OVEN
A4.
ASSEMBLE AND
INSTALL ADAPTOR
A3.
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
You need to drill holes for the top support screws,
a hole large enough for the power cord to fit through,
and a cutout large enough for the exhaust adaptor.
A2.
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT
TWO PEOPLE
INSTALL THIS OVEN.
IMPORTANT: Do not grip or use handle
during installation.
NOTE:
If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE:
We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not
used, case damage may occur from over
tightening screws.
Insert a self-aligning screw through top center
cabinet hole. Temporarily secure the oven by
turning the screw at least
two full turns
after the
threads have engaged
.
(It will be completely
tightened later.)
Be sure to keep power cord tight.
Be careful not to pinch the cord, especially when
mounting flush to bottom of cabinet.
NOTE:
When mounting the
oven, thread power cord
through hole in bottom
of top cabinet. Keep it tight
throughout Steps 1–3.
Do not pinch cord or lift
oven by pulling cord.
Lift oven, tilt it
forward, and hook
slots at back bottom
edge onto two lower
tabs of mounting
plate.
Damper
Back of
Oven
•
Read the instructions on the TOP CABINET
TEMPLATE.
•
Tape it underneath the top cabinet.
•
Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION:
Wear safety goggles when drilling holes
in the cabinet bottom.
Installation Instructions
Place the oven in its upright position, with the top
of the unit facing up.
Insert the tabs on each side of the damper into the
holes at the inside rear of the adaptor.
Attach the exhaust adaptor to the blower plate with
the two bronze metal screws provided.
Make sure that the damper pivots easily before
mounting oven.
You will need to make adjustments to assure proper
alignment with your house exhaust duct after the
oven is installed.
Exhaust
Adaptor
1
2
Blower Plate
3