Gigabyte B560 AORUS PRO AX User Manual - Page 19

SATA3 0/1/2/3/4/5 SATA 6Gb/s Connectors, M2P_CPU, M2A_SB/M2B_SB M.2 Socket 3 Connectors

Get Gigabyte B560 AORUS PRO AX PDF manuals and user guides View all Gigabyte B560 AORUS PRO AX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

B _S S S S_ _ S B_B B _S S S S__ U __ B 8) SATA3 0/1/2/3/4/5 (SATA 6Gb/s CFonnectors) The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA _S 1.5Gb/s standard. Each SATA connector supports a single SATA device. F_USBS_3_ UF __ F B F_USB_3 UF _ B _ S_ F_USB3 F G.QBOFM SATA3 5 3 1 420 G._Q0BOFM G.QBPOinFMNo. Definition 1 GND 2 TXP F 7 1 3 TXN 7 _0 1 4 GND 5 RXN _F 6 RXP _ S_ 7 GND _0 _ S_ To enable hot-plugging for th_e FSATA ports, refer to Chapter 2, "BIOS Setup," "Settings\IO Ports\ SATA And RST Configuration," for more information. _0 F 9) M2P_CPU (Note)/M2A_SB/M2B_S_BF(M.2 Socket 3 Connectors) The M.2 connectors support M.2 SA_T0A SSFDs or M.2 PCIe SSDs. _0 F 110 80 60 M2P_CPU (Note) 110 80 60 M2A_SB _3 U 110 80 60 M2B_SB Follow the steps below to corre_3ctly instUall an M.2 SSD in the M.2 connector. Step 1: Locate the M.2 connector where you will install the M.2 SSD, use a screwdriver to unfasten the screw on the heatsink and then remove the heatsink. Step 2: Locate the proper mounting ho_le3 basedUon the length of your M.2 SSD drive. If needed, move the standoff to the desired mounting hole. Insert the M.2 SSD into the M.2 connector at an angle. Step 3: Press the M.2 SSD down and then use the included screw to secure it in the connector. Replace the heatsink and secure it to the original hole. (Note) Supported by 11th Generation processors only. - 19 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
8)
SATA3 0/1/2/3/4/5 (SATA 6Gb/s Connectors)
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA
1.5Gb/s standard. Each SATA connector supports a single SATA device.
Pin No.
Definition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
To enable hot-plugging for the SATA ports, refer to Chapter 2, "BIOS Setup," "Settings\IO Ports\
SATA And RST Configuration," for more information.
1
1
SATA3
5
3
1
4
2
0
7
7
9)
M2P_CPU
(Note)
/M2A_SB/M2B_SB (M.2 Socket 3 Connectors)
The M.2 connectors support M.2 SATA SSDs or M.2 PCIe SSDs.
80
110
60
80
110
60
80
110
60
M2P_CPU
(Note)
M2A_SB
M2B_SB
(Note)
Supported by 11th Generation processors only.
Follow the steps below to correctly install an M.2 SSD in the M.2 connector.
Step 1:
Locate the M.2 connector where you will install the M.2 SSD, use a screwdriver to unfasten the screw on
the heatsink and then remove the heatsink.
Step 2:
Locate the proper mounting hole based on the length of your M.2 SSD drive. If needed, move the standoff
to the desired mounting hole. Insert the M.2 SSD into the M.2 connector at an angle.
Step 3:
Press the M.2 SSD down and then use the included screw to secure it in the connector. Replace the
heatsink and secure it to the original hole.
- 19 -