Gigabyte C246N-WU2 User Manual - Page 11

HDMI Port, RJ-45 LAN Port, USB 3.1 Gen 1 Port, Mic In Pink, Line Out/Front Speaker Out Green

Get Gigabyte C246N-WU2 PDF manuals and user guides View all Gigabyte C246N-WU2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

HDMI Port The HDMI port supports HDCP 2.2 and Dolby TrueHD and DTS HD Master Audio formats. It also supports up to 192KHz/16bit 8-channel LPCM audio output. You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is 4096x2160@30 Hz, but the actual resolutions supported are dependent on the monitor being used. • To set up a triple-display configuration, you must install motherboard drivers in the operating system first. • After installing the DisplayPort/HDMI device, make sure to set the default sound playback device to DisplayPort/HDMI. (The item name may differ depending on your operating system.) RJ-45 LAN Port The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs. Connection/ Speed LED Activity LED Connection/Speed LED: State Description Activity LED: State Description Orange 1 Gbps data rate Blinking Data transmission or receiving is occurring Green 100 Mbps data rate On No data transmission or receiving is occurring LAN Port Off 10 Mbps data rate USB 3.1 Gen 1 Port The USB 3.1 Gen 1 port supports the USB 3.1 Gen 1 specification and is compatible to the USB 2.0 specification. Use this port for USB devices. Mic In (Pink) The Mic in jack. Line Out/Front Speaker Out (Green) The line out jack. •• When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard. •• When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector. •• The integrated HD (High Definition) audio provides jack retasking capability that allows the user to change the function for each jack through the audio driver. •• To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver. Please go to the Start menu to select Realtek Audio Console, enter the Device advanced settings tab in the lower left corner of the dialog box, and check the option Mute the internal output device, when an external headphone plugged in. to proceed with 7.1-channel settings. Please visit GIGABYTE's website for details on configuring the audio software. - 11 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
•
To set up a triple-display configuration, you must install motherboard drivers in the operating
system first.
•
After installing the DisplayPort/HDMI device, make sure to set the default sound playback
device to DisplayPort/HDMI. (The item name may differ depending on your operating system.)
HDMI Port
The HDMI port supports HDCP 2.2 and Dolby TrueHD and DTS HD Master Audio
formats. It also supports up to 192KHz/16bit 8-channel LPCM audio output. You
can use this port to connect your HDMI-supported monitor. The maximum supported resolution is
4096x2160@30 Hz, but the actual resolutions supported are dependent on the monitor being used.
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following
describes the states of the LAN port LEDs.
USB 3.1 Gen 1 Port
The USB 3.1 Gen 1 port supports the USB 3.1 Gen 1 specification and is compatible to the USB 2.0
specification. Use this port for USB devices.
Mic In (Pink)
The Mic in jack.
Line Out/Front Speaker Out (Green)
The line out jack.
•
When removing the cable connected to a back panel connector, first remove the cable from your
device and then remove it from the motherboard.
•
When removing the cable, pull it straight out from the connector. Do not rock it side to side to
prevent an electrical short inside the cable connector.
Please visit GIGABYTE's website for details on configuring the audio software.
Activity LED
Connection/
Speed LED
LAN Port
Activity LED:
Connection/Speed LED:
State
Description
Orange
1 Gbps data rate
Green
100 Mbps data rate
Off
10 Mbps data rate
State
Description
Blinking
Data transmission or receiving is occurring
On
No data transmission or receiving is occurring
•
The integrated HD (High Definition) audio provides jack retasking capability that allows the user
to change the function for each jack through the audio driver.
•
To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the
multi-channel audio feature through the audio driver. Please go to the Start menu to select
Realtek
Audio Console
, enter the
Device advanced
settings
tab in the lower left corner of the dialog box,
and check the option
Mute the internal output device, when an external headphone plugged
in.
to proceed with 7.1-channel settings.
- 11 -