Gigabyte GA-6PXSV3 Manual - Page 22

F_PANEL1 Front Panel Header

Get Gigabyte GA-6PXSV3 PDF manuals and user guides View all Gigabyte GA-6PXSV3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

10) F_PANEL1 (Front Panel Header) Connect the power switch, reset switch, chassis intrusion switch/sensor and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables. 12 12 24 The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly. Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Signal Name PWLED+ 5VSB NC ID_LED+ PWLED- ID_LED- HD+ F_SYSRDY HD- SYS_STATUS- PWB+ L1_ACT PWB+_GND L1_LINK- RST_BTN+ SENSOR_SDA RST_BTN_GND SENSOR_SCL ID_SW+ CASE_OPEN- ID_SW (GND) L2_ACT NMI_SW- L2_LINK- Definition Power LED Signal anode (+) 5V Stanndby Power No Pin ID LED Signal anode (+) Power LED Signal cathode(-) ID LED Signal cathode(-) Hard Disk LED Signal anode (+) System Front board LED Signal Hard Disk LED Signal cathode(-) System Status LED Signal cathode(-) Power Button Signal anode (+) LAN1 active LED Signal Ground LAN1 Link LED Signal cathode(-) Reset button Signal anode (+) SMBus Data Signal Ground SMBus Clock Signal ID Switch Signal anode (+) Chassis intrusion Signal cathode(-) Ground LAN2 active LED Signal NMI switch Signal cathode(-) LAN2 Link LED Signal cathode(-) Hardware Installation - 22 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Hardware Installation
- 22 -
10) F_PANEL1 (Front Panel Header)
Connect the power switch, reset switch, chassis intrusion switch/sensor and system status indicator on
the chassis to this header according to the pin assignments below. Note the positive and negative pins
before connecting the cables.
1
2
12 24
Pin No.
Signal Name
Deļ¬nition
1
PWLED+
Power LED Signal anode (+)
2
5VSB
5V Stanndby Power
3
NC
No Pin
4
ID_LED+
ID LED Signal anode (+)
5
PWLED-
Power LED Signal cathode(-)
6
ID_LED-
ID LED Signal cathode(-)
7
HD+
Hard Disk LED Signal anode (+)
8
F_SYSRDY
System Front board LED Signal
9
HD-
Hard Disk LED Signal cathode(-)
10
SYS_STATUS-
System Status LED Signal cathode(-)
11
PWB+
Power Button Signal anode (+)
12
L1_ACT
LAN1 active LED Signal
13
PWB+_GND
Ground
14
L1_LINK-
LAN1 Link LED Signal cathode(-)
15
RST_BTN+
Reset button Signal anode (+)
16
SENSOR_SDA
SMBus Data Signal
17
RST_BTN_GND
Ground
18
SENSOR_SCL
SMBus Clock Signal
19
ID_SW+
ID Switch Signal anode (+)
20
CASE_OPEN-
Chassis intrusion Signal cathode(-)
21
ID_SW (GND)
Ground
22
L2_ACT
LAN2 active LED Signal
23
NMI_SW-
NMI switch Signal cathode(-)
24
L2_LINK-
LAN2 Link LED Signal cathode(-)
The front panel design may differ by chassis.
A front panel module mainly consists of power
switch, reset switch, power LED, hard drive ac-
tivity LED, speaker and etc. When connecting
your chassis front panel module to this header,
make sure the wire assignments and the pin
assignments are matched correctly.