Gigabyte GA-F2A88XM-HD3P User Manual - Page 14

SATA3 0/1/2/3/4/5/6/7 SATA 6Gb/s Connectors, F_PANEL Front Panel Header, PW Power Switch

Get Gigabyte GA-F2A88XM-HD3P PDF manuals and user guides View all Gigabyte GA-F2A88XM-HD3P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

5) SATA3 0/1/2/3/4/5/6/7 (SATA 6Gb/s Connectors) The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. The AMD Chipset supports RAID 0, RAID 1, RAID 5, RAID 10, and JBOD. Refer to Chapter 3, "Configuring a RAID Set," for instructions on configuring a RAID array. 1DEBUG PORT Pin No. Definition SATA3DPOE7BRUTG 1 GND 2 TXP 3 TXN SATA3 6 7 4 SATA3 5 7 1 7 1 4 5 G.QBOFM6 7 G.QBOFM GND RXN RXP GND To enable hot-plugging for the SATA ports, refer to Chapter 2, "BIOS Setup," "Peripherals\SATA Configuration," for more information. DEBUG PORT DEBUG PORT SATA3 1 7 1 1 77 1 2 1 7 SATA3 3 SATA3 0 6) F_PANEL (Front Panel Header) Connect the power switch, reset switch, and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables. Power/ Sleep LED Power Switch PLED+ PLED- PW+ PW- 2 10 1 9 HD+ HD- RESRES+ NC Hard Drive Reset Switch Activity LED •• PLED(Power/Sleep LED): System Status LED S0 On S3/S4/S5 Off Connects to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED is off when the system is in S3/S4 sleep state or powered •• PW (Power Switch): off (S5). Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management," for more information). •• HD (Hard Drive Activity LED): Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data. •• RES (Reset Switch): Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart. •• NC: No connection. The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly. - 14 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
- 14 -
5)
SATA3 0/1/2/3/4/5/6/7 (SATA 6Gb/s Connectors)
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s
standard. Each SATA connector supports a single SATA device. The AMD Chipset supports RAID 0, RAID 1,
RAID 5, RAID 10, and JBOD. Refer to Chapter 3, "Configuring a RAID Set," for instructions on configuring a
RAID array.
Pin No.
Definition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
7
1
4
5
7
1
7
7
1
SATA3
To enable hot-plugging for the SATA ports, refer
to Chapter 2, "BIOS Setup," "Peripherals\SATA
Configuration," for more information.
6)
F_PANEL (Front Panel Header)
Connect the power switch, reset switch, and system status indicator on the chassis to this header according
to the pin assignments below. Note the positive and negative pins before connecting the cables.
•
PW (Power Switch):
Connects to the power switch on the chassis front panel. You may configure
the way to turn off your system using the power switch (refer to Chapter
2, "BIOS Setup," "Power Management," for more information).
•
HD (Hard Drive Activity LED):
Connects to the hard drive activity LED on the chassis front panel. The
LED is on when the hard drive is reading or writing data.
•
RES (Reset Switch):
Connects to the reset switch on the chassis front panel. Press the reset
switch to restart the computer if the computer freezes and fails to perform
a normal restart.
•
NC:
No connection.
•
PLED(Power/Sleep LED):
System Status
LED
S0
On
S3/S4/S5
Off
Connects to the power status indicator on the
chassis front panel. The LED is on when the
system is operating. The LED is off when the
system is in S3/S4 sleep state or powered
off (S5).
The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch,
power LED, hard drive activity LED and etc. When connecting your chassis front panel module to this header,
make sure the wire assignments and the pin assignments are matched correctly.
1
2
9
10
NC
PLED-
PW-
PLED+
PW+
HD-
RES+
HD+
RES-
Power/
Sleep LED
Power Switch
Hard Drive
Activity LED
Reset Switch
6
SATA3
0
SATA3
1
SATA3
1
1
SATA3
7
7
2
3
1
1
SATA3
7
7