Gigabyte GA-G33-DS3R Manual - Page 31

CLR_CMOS Clearing CMOS Jumper, HDMI_AC HDMI Adapter Audio Cable Connector - bios update

Get Gigabyte GA-G33-DS3R PDF manuals and user guides View all Gigabyte GA-G33-DS3R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

English 19) CLR_CMOS (Clearing CMOS Jumper) Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset the CMOS values to factory defaults. To clear the CMOS values, place a jumper cap on the two pins to temporarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few seconds. Open: Normal Short: Clear CMOS Values • Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values. • After clearing the CMOS values and before turning on your computer, be sure to remove the jumper cap from the jumper. Failure to do so may cause damage to the motherboard. • After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or manually configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS configurations). 20) HDMI_AC (HDMI Adapter Audio Cable Connector) When the HDMI adapter is installed in the PCI Express x16 slot for HDMI video output, you may connect the adapter's HD audio cable to the connector for HDMI audio output. Pin No. 1 2 3 4 5 6 7 8 2 16 1 15 Definition ACZ_BITCLK GND -ACZ_RST VCC3 ACZ_SYNC GND ACZ_SDOUT VCC3 Pin No. 9 10 11 12 13 14 15 16 Definition ACZ_SDIN0 +12V ACZ_SDIN1 No Pin ACZ_SDIN3 3VDUAL ACZ_SDIN2 GND To enable HDMI, make sure the "Microsoft UAA Bus driver for High Definition Audio" has been installed from the motherboard driver disk and your operating system has been updated with the latest Service Pack for Windows before installing the graphics card driver. - 31 - Hardware Installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Hardware Installation
- 31 -
English
Open: Normal
Short: Clear CMOS Values
19)
CLR_CMOS (Clearing CMOS Jumper)
Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and
reset the CMOS values to factory defaults. To clear the CMOS values, place a jumper cap on the
two pins to temporarily short the two pins or use a metal object like a screwdriver to touch the two
pins for a few seconds.
•
Always turn off your computer and unplug the power cord from the power outlet before
clearing the CMOS values.
•
After clearing the CMOS values and before turning on your computer, be sure to remove
the jumper cap from the jumper. Failure to do so may cause damage to the motherboard.
•
After system restart, go to BIOS Setup to load factory defaults (select
Load Optimized
Defaults
) or manually configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for
BIOS configurations).
20)
HDMI_AC (HDMI Adapter Audio Cable Connector)
When the HDMI adapter is installed in the PCI Express x16 slot for HDMI video output, you may
connect the adapter's HD audio cable to the connector for HDMI audio output.
Pin No.
Definition
1
ACZ_BITCLK
2
GND
3
-ACZ_RST
4
VCC3
5
ACZ_SYNC
6
GND
7
ACZ_SDOUT
8
VCC3
Pin No.
Definition
9
ACZ_SDIN0
10
+12V
11
ACZ_SDIN1
12
No Pin
13
ACZ_SDIN3
14
3VDUAL
15
ACZ_SDIN2
16
GND
1
2
15
16
To enable HDMI, make sure the "Microsoft UAA Bus driver for High Definition Audio" has
been installed from the motherboard driver disk and your operating system has been
updated with the latest Service Pack for Windows before installing the graphics card driver.