Gigabyte GA-H61M-WW Manual - Page 13

SATA2 0/1/2/3 SATA 3Gb/s Connectors, F_PANEL Front Panel Header, SPEAKER Speaker Header

Get Gigabyte GA-H61M-WW PDF manuals and user guides View all Gigabyte GA-H61M-WW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

DEBUG PORT DEBUG PORT DEBUG PORT 5) SATA2 0/1/2/3 (SATA 3Gb/s Connectors) The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. 1 3 SATA2 Pin No. Definition 1 7 1 GND 0 2 TXP 1 1 7 3 TXN 4 GND 7 5 RXN 2 6 RXP 7 GND 6) F_PANEL (Front Panel Header) Connect the power switch, reset switch, and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables. HD+ HD- RESRES+ NC PLED+ PLED- PW+ PW- Power Power LED Switch 2 1 Hard Drive Reset Activity LED Switch •• PLED (Power LED): System Status LED Connects to the power status indicator S0 On S3/S4/S5 Off on the chassis front panel. The LED is on when the system is operating. The LED is off when the system is in S3/S4 sleep state •• PW (Power Switch): or powered off (S5). Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management," for more information). •• HD (Hard Drive Activity LED): Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data. •• RES (Reset Switch): Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart. The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, hard drive activity LED and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly. 7) SPEAKER (Speaker Header) This header connects to the speaker on the chassis front panel. The system reports system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup. Pin No. Definition 1 SPK+ 2 NC 1 3 NC 4 SPK- - 13 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
- 13 -
5)
SATA2 0/1/2/3 (SATA 3Gb/s Connectors)
The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard.
Each SATA connector supports a single SATA device.
Pin No.
Definition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
6)
F_PANEL (Front Panel Header)
Connect the power switch, reset switch, and system status indicator on the chassis to this header according
to the pin assignments below. Note the positive and negative pins before connecting the cables.
•
PW
(Power Switch):
Connects to the power switch on the chassis front panel. You may
configure the way to turn off your system using the power switch
(refer to Chapter 2, "BIOS Setup," "Power Management," for more
information).
•
HD
(Hard Drive Activity LED):
Connects to the hard drive activity LED on the chassis front panel. The
LED is on when the hard drive is reading or writing data.
•
RES
(Reset Switch):
Connects to the reset switch on the chassis front panel. Press the
reset switch to restart the computer if the computer freezes and fails
to perform a normal restart.
•
PLED
(Power LED):
System Status
LED
S0
On
S3/S4/S5
Off
Connects to the power status indicator
on the chassis front panel. The LED is on
when the system is operating. The LED is
off when the system is in S3/S4 sleep state
or powered off (S5).
The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch,
hard drive activity LED and etc. When connecting your chassis front panel module to this header, make sure the
wire assignments and the pin assignments are matched correctly.
1
2
PLED-
PW-
PLED+
PW+
Power
LED
HD-
RES+
HD+
RES-
Hard Drive
Activity LED
Reset
Switch
Power
Switch
7
1
7
1
1
7
0
1
SATA2
3
2
NC
7)
SPEAKER (Speaker Header)
This header connects to the speaker on the chassis front panel. The system reports system startup status
by issuing a beep code. One single short beep will be heard if no problem is detected at system startup.
Pin No.
Definition
1
SPK+
2
NC
3
NC
4
SPK-
1