Gigabyte GA-H87M-HD3 User Manual - Page 14
SATA3 0/1/2/3/4/5 SATA 6Gb/s Connectors, F_PANEL Front Panel Header, Speaker, PLED/PWR
View all Gigabyte GA-H87M-HD3 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
5) SATA3 0/1/2/3/4/5 (SATA 6Gb/s Connectors) The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. The Intel® Z87j/H87k Chipset supports RAID 0, RAID 1, RAID 5, and RAID 10. Refer to Chapter 3, "Configuring SATA Hard Drive(s)," for instructions on configuring a RAID array. 77 Pin No. Definition 1 GND 2 TXP SATA3 54 3 TXN 4 GND 32 5 RXN 10 6 RXP 7 GND 11 6) F_PANEL (Front Panel Header) Connect the power switch, reset switch, speaker, and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables. Power Power LED Switch Speaker •• PLED/PWR (Power LED): System Status LED S0 On S3/S4/S5 Off Connects to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED is off when the system is in S3/S4 sleep state PLED+ PLED- PW+ PWSPEAK+ SPEAK- F_PANEL(NH) 2 1 or powered off (S5). 20 19 •• PCWonn(F(PHe_6Poc1AwtMsNe-EDtrLo2S) twheitcpho):wer switch PWM Switch (SW1)(X79-UD7) on the chassis front panel. You may DIP 12345 configure the way to turn off your system using the power switch HD+ HD- RESRES+ CICI+ PWR_LED+ PWR_LEDPWR_LED- (refer to Chapter 2, "BIOS Setup," "Power Management," for more information). •• Speaker (Speaker): Hard Drive Reset Activity LED Switch Power LED Chassis Intrusion Header Connects to the speaker on the chassis front panel. The system reports system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup. •• HD (Hard Drive Activity LED): BIOS Switcher (X58A-OC) Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data. DIP 1 23 1 1 M_SATA •• RES (Reset Switch): Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails DIP 1 23 1 DIP 1 23 1 to perform a normal restart. •• CI (CAhCaPsI_sCisPTIntrusion Header): BIOS_PH Conn(GeAc-tIsVBto) the chassis intrusion switch/sensor on(GtAh-eIVcBh) assis that can PWM Switch (X58A-OC) detect if the chassis cover has been removed. This function requires a chassis with a chassis intrusion switch/sensor. The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, DIP power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this 1 23 header, make sure the wire assignmenStMs Ba_nCdPtThe pin assignments are matched correctly. (GA-IVB) MM Only for GA-Z87M-HD3. NN Only for GA-H87M-HD3. - 14 - CLR_CMOS CI DIS_ME GP15_CPT (GA-IVB)