Gigabyte GA-K8NF9 Ultra Manual - Page 2

Configuring SATA Hard Drives Controller: nVIDIA nForce4 Ultra, nVIDIA nForce4 SLI

Page 2 highlights

Ác Configuring SATA Hard Drive(s) (Controller: nVIDIA nForce4 Ultra; Åé nVIDIA nForce4 SLI) ¤¤ ¤å To configure SATA hard drive(s), follow the steps below: (1) Install SATA hard drive(s) in your system. (2) Configure SATA controller mode and boot sequence in BIOS Setup. (3)* Configure RAID set in RAID BIOS. (4) Make a floppy disk containing the SATA controller driver. (5) Install the SATA controller driver during OS installation. Before you begin Please prepare: (a) At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard drives with identical model and capacity). If you do not want to create RAID, you may prepare only one hard drive. (b) An empty formatted floppy disk. (c) Windows XP/2000 setup disk. (d) Driver CD for your motherboard. (1) Installing SATA hard drive(s) in your computer Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port(s) on the motherboard. (If there are more than one SATA controller on your motherboard, you may check the name of the SATA connector to identify the SATA controller for the connector. For example, S_ATA1_SB/S_ATA2_SB is controlled by the SATA controller on South-Bridge.) Then connect the power connector from your power supply to the hard drive. "*" Skip this step if you do not want to create RAID array on the SATA controller. SATA Hard Drive Configurations (nForce series) - 2 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16

SATA Hard Drive Configurations (nForce series)
- 2 -
Ác
Åé
¤¤
¤å
Configuring SATA Hard Drive(s) (Controller: nVIDIA nForce4 Ultra;
nVIDIA nForce4 SLI)
"*"
Skip this step if you do not want to create RAID array on the SATA controller.
To configure SATA hard drive(s), follow the steps below:
(1)
Install SATA hard drive(s) in your system.
(2)
Configure SATA controller mode and boot sequence in BIOS Setup.
(3)* Configure RAID set in RAID BIOS.
(4)
Make a floppy disk containing the SATA controller driver.
(5)
Install the SATA controller driver during OS installation.
Before you begin
Please prepare:
(a)
At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two
hard drives with identical model and capacity). If you do not want to create RAID, you may prepare
only one hard drive.
(b)
An empty formatted floppy disk.
(c)
Windows XP/2000 setup disk.
(d)
Driver CD for your motherboard.
(1)
Installing SATA hard drive(s) in your computer
Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available
SATA port(s) on the motherboard. (If there are more than one SATA controller on your motherboard, you
may check the name of the SATA connector to identify the SATA controller for the connector. For example,
S_ATA1_SB/S_ATA2_SB is controlled by the SATA controller on South-Bridge.) Then connect the power
connector from your power supply to the hard drive.