Gigabyte GA-Z270X-Gaming 8 Users Manual - Page 61

Peripherals, Initial Display Output, OnBoard LAN Controller Rivet Networks Killer, E2500 LAN Chip

Get Gigabyte GA-Z270X-Gaming 8 PDF manuals and user guides View all Gigabyte GA-Z270X-Gaming 8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

2-6 Peripherals && Initial Display Output Specifies the first initiation of the monitor display from the installed PCI Express graphics card or the onboard graphics. IGFX Sets the onboard graphics as the first display. PCIe 1 Slot Sets the graphics card on the PCIEX16 slot as the first display. (Default) PCIe 2 Slot Sets the graphics card on the PCIEX8 slot as the first display. PCIe 3 Slot Sets the graphics card on the PCIEX4_1 slot as the first display. PCIe 4 Slot Sets the graphics card on the PCIEX4_2 slot as the first display. && OnBoard LAN Controller (Rivet Networks Killer™ E2500 LAN Chip, LAN2) Enables or disables the Rivet Networks Killer™ E2500 LAN function. (Default: Enabled) If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to Disabled. && EZ RAID Allows you to quickly set up a RAID array. Refer to Chapter 3, "Configuring a RAID Set," for instructions on configuring a RAID array. && Rear Panel LED Enables or disables the audio LED on the rear panel I/O shield. On The LED will light and follow the behavior of the onboard audio LEDs. (Default) Off Disables this function. && LED_C1 Connect Enables or disables the lights of the RGB (RGBW) LED strip connected to the LED_C1 header on the motherboard. (Default: Enabled) && LED_C2 Connect Enables or disables the lights of the RGB (RGBW) LED strip connected to the LED_C2 header on the motherboard. (Default: Enabled) - 61 - BIOS Setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
BIOS Setup
- 61 -
&
Initial Display Output
Specifies the first initiation of the monitor display from the installed PCI Express graphics card or the onboard
graphics.
±
IGFX
Sets the onboard graphics as the first display.
±
PCIe 1 Slot
Sets the graphics card on the PCIEX16 slot as the first display. (Default)
±
PCIe 2 Slot
Sets the graphics card on the PCIEX8 slot as the first display.
±
PCIe 3 Slot
Sets the graphics card on the PCIEX4_1 slot as the first display.
±
PCIe 4 Slot
Sets the graphics card on the PCIEX4_2 slot as the first display.
&
OnBoard LAN Controller (Rivet Networks Killer
™
E2500 LAN Chip, LAN2)
Enables or disables the Rivet Networks Killer
™
E2500 LAN function. (Default: Enabled)
If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to
Disabled
.
&
EZ RAID
Allows you to quickly set up a RAID array. Refer to Chapter 3, "Configuring a RAID Set," for instructions
on configuring a RAID array.
&
Rear Panel LED
Enables or disables the audio LED on the rear panel I/O shield.
±
On
The LED will light and follow the behavior of the onboard audio LEDs. (Default)
±
Off
Disables this function.
&
LED_C1 Connect
Enables or disables the lights of the RGB (RGBW) LED strip connected to the LED_C1 header on the
motherboard. (Default: Enabled)
&
LED_C2 Connect
Enables or disables the lights of the RGB (RGBW) LED strip connected to the LED_C2 header on the
motherboard. (Default: Enabled)
2-6
Peripherals