Gigabyte MP30-AR1 Manual - Page 1

MP30-AR1 Quick Reference Guide 12 3 4 5 67 30 29 31 33 28 32 27 35 26 36 8 9 10 25 24 37 34 38 11 13 12 23 22 21 14 No. Code Description 1 LED_STA System status LED 2 USB2_MLAN KVM Server Management 10/100/1000 LAN port (top)/USB 2.0 ports (bottom) 3 VGA1_COM1 Serial port (top)/VGA port (bottom) 4 SFP+_1_2 SFP+ LAN port #1/#2 5 LAN1_2 GbE LAN port #1/#2 6 SW_PWR Power button with LED 7 SW_ID ID switch button with LED 8 CPU_FAN CPU fan connector 9 DIMM_P0_A0 Channel 1 slot 0 10 DIMM_P0_A1 Channel 1 slot 1 11 DIMM_P0_B0 Channel 2 slot 0 12 DIMM_P0_B1 Channel 2 slot 1 13 CPU0 AppliedMicro® X-Gene 1 processor 14 P12V_AUX 14 pin power connector 15 ATX1 24 pin main power connector 16 SYS_FAN1 System fan connector#1 17 FP_1 Front panel header (for Server system) 18 SYS_FAN2 System fan connector#2 19 PMBUS PMBus header 20 CLR_CMOS Clear CMOS jumper No. Code 21 SYS_FAN3 22 BP_1 23 CASE_OPEN 24 IPMB 25 SYS_FAN4 26 SATA_DOM0 27 SATA0 28 SATA1 29 SATA2 30 SATA3 31 PCIE_2 32 BAT 33 PCIE_1 34 LED_BMC 35 DIMM_P0_C0 36 DIMM_P0_C1 37 DIMM_P0_D0 38 DIMM_P0_D1 Description System fan connector#3 HDD back plane board header Case open intrusion alert header IPMB connector System fan connector#4 SATA port 3 DOM support jumper SATA 3 6Gb/s connector SATA 3 6Gb/s connector SATA 3 6Gb/s connector SATA 3 6Gb/s connector PCI Express x16 slot Battery socket PCI Express x16 slot BMC firmwar readiness LED Channel 3 slot 0 Channel 3 slot 1 Channel 4 slot 0 Channel 4 slot 1 Rear I/O Connector 1 3 5 No. Desription 1 GbE LAN ports 2 SFP+ LAN ports 2 2 3 7 4 5 Serial port VGA port KVM Server Management 10/100/1000 LAN port (Dedicated LAN port) 6 USB 2.0 ports 7 System Status LED 1 4 6 20 19 18 17 16 15 Speed LED Link/Activity LED ATX Power/ 䕚๕ IPMB SATA Connector/SATA 接口 24 13 12 1 No. Pin Define No. Pin Define 1 3.3V 13 3.3V 2 3.3V 14 -12V 3 GND 15 GND 4 +5V 16 PS_ON 5 GND 17 GND 6 +5V 18 GND 7 GND 19 GND 8 Power Good 20 -5V 9 5VSB 21 +5V 10 +12V 22 +5V 11 +12V 23 +5V 12 3.3V 24 GND 3 4 No. 1 2 1 2 Pin Define No. GND 3 GND 4 Pin Define +12V +12V No. Pin Define 1 31 Clock 2 GND 3 Data CPU/System FAN/ 䔎ࣂ 4 1 No. 1 1 2 3 4 4 Pin Define GND +12V Sense Speed Control 7 No. 1 2 3 4 1 Pin DefineNo. GND 5 TXP 6 TXN 7 GND Pin Define RXN RXP GND BMC Firmware Readiness LED BMC Firmware Readiness LED (LED_BMC): State Description On BMC firmware is initial Blink BMC firmware is ready Off AC loss Speed LED Link/Activity LED Speed LED Link/Activity LED Chassis Intrusion Alert Header Open: Normal operation. Closed: Active chassis intrustion alert. 1 No 1 2 3 5 PMBUS Pin Define No SMB CLK 4 SMB DATA 5 SMB ALERT Pin Define GND 3.3V SENSE Front Panel Header HDD Back Plane Board Header 2 2 24 No. Pin Define No. Pin Define 1 23 12 1 BP_SGP_CLK 2 No Connect 3 BP_SGP_LD 4 FAN_Gate No. Pin Define No. Pin Define 1 Power LED+ 2 5V Standby 3 No Pin 4 ID LED+ 5 Power LED- 6 ID LED- 7 HDD LED+ 8 System Status LED+ 9 HDD LED- 10 System Status LED- 11 Power Button 12 LAN1 Active LED+ 13 GND 14 LAN1 Link LED- 15 Reset Button+ 16 SMBus Data 17 GND 18 SMBus Clock 19 ID Switch+ 20 Case Open 5 7 9 11 13 15 17 25 26 19 21 23 25 BP_SGP_DOUT 6 Key Pin 8 GND 10 BP_LED_G_N 12 BP_SGP_DIN 14 GND 16 GND 18 P_3V3_AUX 20 P_3V3_AUX 22 GND 24 BP_PRESENSE 26 GND Reset BP_LED_A_N GND No Connect SMB_BP_DATA SMB_BP_CLK BMC_ACK BMC_REQ Key Pin GND 1 21 ID Switch- 22 LAN2 Active LED 23 NMI Switch- 24 LAN2 Link LED- 10/100/1000 LAN LED: State Yellow On Description 1Gbps data arte Green On 100Mbps data arte Off 10Mbps data arte SFP+ LAN LED: State Green On Description 10 Gbps data rate Green Blink Identify 10 Gbps data rate Yellow On 1 Gbps data rate Yellow Blink Identify 1 Gbps data rate Off 100 Mbps data rate System Status LED: State Description Green On Green Blink System is operating normally. Degrade condition, may indicates the following:  CPU failure  DIMM killed Amber On Critical condition, may indicates the following:  Power module failure  System fan failure  Power supply voltage issue  System temperature/voltage issue Amber Blink Non-critical condition, may indicates the following:  Redundant power module failure  Temperature and voltage issue  Chassis intrusion System is not ready. May indicate the following: POST error N/A NMI error Processor or terminator missing 系统状态LED: 说明 无亮灯 POST错误 NMI Jumper Settings Memory Population Configuration No. Desription 1 Clear CMOS Jumper 1-2 Close: Normal operation (Default setting) 2-3 Close: Clear CMOS data. 2 SATA Port 3 DOM Support Jumper Jumper 1-2 Close: Enable SATA port DOM support funtion. 2-3 Close: Normal Operation. (Default setting) If a SATA type hard drive is connected to the motherboard, please ensure the jumper is closed and set to 2-3 pins (Default setting), in order to reduce any risk of hard disk damage. Pin No. Definition 1 P5V 2 SATA3 Pin7 3 GND Slot Per Channel (SPC) and DIMM Per Channel (DPC) 1 Slot 2 Slot 4 Slot 8 Slot 1DPC 1DPC 2DPC A0+B0 A0+A1 A0 or C0 or or A0+C0 C0+C1 1DPC 2DPC 2DPC A0+B0 A0+A1+B0+B1 and or Inser Full C0+D0 A0+A1+C0+D0 PN