Gigabyte R121-X30 Manual - Page 1
Gigabyte R121-X30 Manual
View all Gigabyte R121-X30 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
R121-X30 Quick Installation Guide/R121-X30 38 34 33 35 36 37 1 2 3 4 32 31 30 29 28 19 27 26 25 24 23 22 21 20 18 17 16 8 9 10 11 15 Motherboard Components No. 1 5 2 3 4 5 6 67 8 7 9 10 11 12 13 14 15 16 17 18 12 19 20 13 21 22 23 14 24 25 26 27 28 29 30 Code USB3_LAN1 USB2_LAN2 VGA COM1 BUZZER PMBUS P2 DIMM_P0_B1 DIMM_P0_B0 DIMM_P0_A1 DIMM_P0_A0 BIOS_RCVR ME_RCVR CASE_OPEN P1 CPU0_FAN CPU0 BAT CLR_CMOS BIOS_PWD SATA_0_1 SATA_2_3 SATA_DOM4 SATA4/SATA5 SATA_DOM5 USB_A1 F_USB3 F_USB2 FP_1 IPMB Description LAN port #1 (top/server management LAN port) / USB 3.0 ports (bottom) LAN port #2 (top) / USB 2.0 ports (bottom) VGA port Serial port Buzzer PMBus connector 8 pin power connector (for CPU) Channel 2 slot 1 Channel 2 slot 0 Channel 1 slot 1 Channel 1 slot 0 BIOS recovery jumper 1-2 Close: Normal operation. (Default setting) 2-3 Close: BIOS recovery mode. ME recovry jumper 1-2 Close: Normal operation. (Default setting) 2-3 Close: ME recovery mode. Case open intrusion alert header 24 pin main power connector CPU fan connector Intel LGA1151 Socket H4 Battery socket Clear CMOS jumper Clearing Supervisor Password jumper 1-2 Close: Normal operation. (Default setting) 2-3 Close: Skip supervisor password. SATA 3 6Gb/s connectors SATA 3 6Gb/s connectors SATA port 4 DOM power connector SATA 3 6Gb/s connectors (Supports SATA DOM) header SATA port 5 DOM power connector Type A USB 2.0 connector USB 3.0 header USB 2.0 header Front panel header IPMB connector No. Code Description 31 M2_MKEY M.2 slot (Dimension: 2280) 32 TPM TPM module connector 33 BP_1 HDD back plane board header 34 COM2 Serial port cable connector 35 PCIE_1 PCI Express x8 slot 36 PCIE_2 PCI Express x16 slot 37 ME_UPDATE ME update jumper 38 S3_MASK S3 Power On Select jumper 1-2 Close: Stop an initial power on when BMC is not ready. 2-3 Close: Keep initial power on. (Default setting) No. 12 1 3 5 7 9 11 13 15 17 23 24 19 21 23 Front Panel Header Pin Define No. Power LED+ 2 No Pin 4 Power LED- 6 HDD LED+ 8 HDD LED- 10 Power Button 12 GND 14 Reset Button+ 16 GND 18 ID Switch+ 20 ID Switch- 22 NMI Switch- 24 Pin Define 5V Standby ID LED+ ID LEDSystem Front Board LED+ System Status LEDLAN1 Active LED+ LAN1 Link LEDSMBus Data SMBus Clock Case Open LAN2 Active LED LAN2 Link LED- 12 25 26 HDD Back Plane Board Header No. Pin Define No. Pin Define 1 BP_SGP_CLK 2 No Connect 3 BP_SGP_GLD 4 FAN_SGP_Gate 5 BP_SGP_DOUT 6 GND 7 Key Pin 8 Reset 9 GND 10 BP_LED_A_N 11 BP_LED_G_N 12 GND 13 BP_SGP_DIN 14 No Connect 15 GND 16 SMB_BP_DATA 17 GND 18 SMB_BP_CLK 19 P_3V3_AUX 20 BMC_ACK 21 P_3V3_AUX 22 BMC_REQ 23 GND 24 Key Pin 25 BP_PRESENSE 26 GND System Cover 1 1 1 1 2 System Components 9 2 34 7 8 10 56 1 CAUTION! Before you remove or install the system cover: Make sure the system is not turned on or connected to AC power. 注意! No Description 1 HDD bays 2 System fan #14 (FAN14) 3 System fan #12 (FAN12) 4 System fan #8 (FAN8) 5 System fan #6 (FAN6) 6 System fan #4 (FAN4) 7 CPU heat sink 8 Memory slots 9 PCIe riser bracket 10 Power supply cage CAUTION! To connect system fan connector, follow the instruction: Blue/Red cable connect to odd numbered connector. White/Amber cable connect to even numbered connector. Fan Duct 2 1 Heat Sink 1 3 2 System Fan 1 2 CAUTION! Before you remove or install the system fan: Make sure the system is not turned on or connected to the AC power. Disconnect all necessary cable connections. Failure to observe these warnings could result in personal injury or damage to the equipment Memory Population Configuration Type Ranks Per DIMM and Data Width Supported Voltage UDIMM Unbuffered SR DDR4 ECC UDIMM Unbuffered DR DDR4 non-ECC 1.2V 1.2V Speed (MT/s); Slot Per Channel (SPC) and DIMM Per Channel (DPC) 2 Slot Per Channel 1DPC 2DPC 2133 2133 2133 2133 All channels in system run at the fastest common frequency. Mixing ECC and non-ECC UDIMMs anywhere on the platform is not supported. 1 and 2 DPC is supported at 2133MHz. ECC与非ECC 1 2 DPC ѩ˕ܵ2133MHz 3 2 1 4 4 Hard Disk Drive and Back Plane Board HDD Backplane Board Components 67 89 5 4 11 12 10 13 14 3 15 16 17 18 2 19 20 21 22 1 No Description 1 HDD#3 2 HDD#2 3 HDD#1 4 HDD#0 5 SGPIO header 6 Fan connector#13 7 Fan connector#14 8 Fan connector#11 9 Fan connector#12 10 ODD power connector 11 Fan connector#9 No Description 12 Fan connector#10 13 Fan connector#7 14 Fan connector#8 15 Fan connector#5 16 Fan connector#6 17 Fan connector#3 18 Fan connector#4 19 Fan connector#1 20 Fan connector#2 21 Fan connector#15 22 Fan connector#16 PCI Express Card 1 4 3 2 Power Supply 1 4 CAUTION! Before you remove or install the power supplies: Make sure the system is not turned on or connected to AC power. 注意! Front & Rear System Front View 123 4 No Description 1 USB 3.0 ports 2 ID button with LED 3 Power button with LED 4 HDD bays System Rear View 12 3 4567 8 9 Power button/LED: State Description Green On System is powered on Off System is powered off Speed LED Link/Activity 10/100/1000 LAN LED: LED State Description Yellow On 1Gbps data rate No Description 1 Power supply module cord socket 2 Power supply fan 3 Serial port 4 VGA port 5 USB 2.0 ports 6 GbE LAN port 7 10/100/1000 Server management LAN port 8 USB 3.0 ports 9 Low-profle riser card bay Green On Off 100Mbps data rate 10Mbps data rate Front Panel LED and Buttons 7 6 54 3 2 1 3 2 5 7 6 4 CAUTION! Before you remove or install the PCI express card: Make sure the system is not turned on or connected to AC power No. Name 1/6 LAN3/4 Active/Link LEDs LAN1/2 Active/Link LEDs Color Green Green Status Solid On Blink Description Link between system and network or no access. Data transmission or receiving is occurring. N/A Off No data transmission or receiving is occurring. 2 Power Button and LED 3 ID Button Green Green N/A Solid On Blink Off System is powered on. System is in ACPI S1 state (sleep mode). System is not powered on or in ACPI S5 state (power off). System is in ACPI S4 state (hibernate mode). Press the button to activate system identifcation. 4 System Status LED 5 HDD Status LED Green 颜色 Amber N/A Green Solid On 状O态ff Solid On Blink N/A On Blink System is operating normally. Degrade condition, may indicates: CPU failure DIMM killed Critical condition, may indicates: Power module failure System fan failure Power supply voltage issue System temperature Non-critical condition, may indicates: Redundant power module failure Temperature and voltage issue Chassis intrusion System is not ready, may indicates: POST error NMI error Processor or terminator missing HDD locate HDD access 7 Reset Button Amber Green/Amber N/A On Blink Off HDD access HDD fault No HDD access or no HDD fault. Press the button to reset the system. 34 编号 1/6 名称 LAN3/LAN4活动LED LAN1/LAN2活动LED 3 LED 3 ID按钮 4 LED 绿色 橙色 6 LED 7 复位按钮 无亮灯 恒亮 闪烁 说明 系统处于ACPI S1 ACPIS5 ACPI S4 POST错误 NMI Rail Kit Release Lock out M6-NUT M6X13 Click Bracket Release lock in M4X6 1 Release and detach the inner member from the slide 2 A⯭ƩⅬac彏h t擨heᷱun㜡it⏗to the inner member 3 Fix the outer member/bracket assembly to the frame 4 Insert the unit to complete the installaƟon