Gigabyte X570 AORUS ELITE User Manual - Page 21

F_PANEL Front Panel Header, F_USB31C USB Type-C, Header with USB 3.2 Gen 2 Support, SPEAK

Get Gigabyte X570 AORUS ELITE PDF manuals and user guides View all Gigabyte X570 AORUS ELITE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

S_ _ B _U _ __ 3 B F 12) F_PANEL (Front Panel Header) Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator on the chassis to tFh_isUShBe3adFer according to the pin assignments below. Note the positive and negative pins before connecting the cables. Power LED Power Switch Speaker •• PLED/PWR_LED (Power LED): _0 System Status LED Connects to the power status indicator PLED+ PLED- PW+ PWSPEAK+ NC NC SPEAK- S0 On on the chassis front panel. The LED is on _ _B S3/S4/S5 Off when the system is operating. The LED is _ S_ off when the system is in S3/S4 sleep state 2 20 or powered off (S5). 1 19 •• PW (Power Switch): _F HD+ HD- RESRES+ CICI+ PWR_LED+ PWR_LEDPWR_LED- Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (refer to Chapter 2, "BIOS Setup," "Settings\Platform Power," for more Hard Drive Activity LED Reset Switch Power LED Chassis Intrusion Header information). •• SPEAK (Speaker): Connects to the speaker on the chassis front pa_ n0el. ThFe system reports system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup. •• HD (Hard Drive Activity LED): Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data. •S• RF_ES (Reset Switch): Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart. •• CI (Chassis Intrusion Header): B ConnectsBt_o the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has been removed. This function requires a chassis with a chassis intrusion switch/sensor. •• NC: No Connection. The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments a_n3d the pUin assignments are matched correctly. 13) F_USB31C (USB Type-C™ Header with USB 3.2 Gen 2 Support) The header conforms to USB 3.2 Gen 2 specification and can provide one USB port. F_USB3 F_USB30 3 10 11 1 20 Pin No. 1 2 3 4 5 6 7 Definition VBUS TX1+ TX1GND RX1+ RX1VBUS Pin No. 8 9 10 11 12 13 14 Definition CC1 SBU1 SBU2 VBUS TX2+ TX2GND Pin No. 15 16 17 18 19 20 Definition RX2+ RX2GND DD+ CC2 - 21 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
The front panel design may differ by chassis. A front panel module mainly consists of power switch,
reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis
front panel module to this header, make sure the wire assignments and the pin assignments are
matched correctly.
12) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator
on the chassis to this header according to the pin assignments below. Note the positive and negative pins
before connecting the cables.
System Status
LED
S0
On
S3/S4/S5
Off
•
PW
(Power Switch):
Connects to the power switch on the chassis front panel. You may
configure the way to turn off your system using the power switch
(refer to Chapter 2, "BIOS Setup," "Settings\Platform Power," for more
information).
•
SPEAK
(Speaker):
Connects to the speaker on the chassis front panel. The system reports
system startup status by issuing a beep code. One single short beep
will be heard if no problem is detected at system startup.
•
PLED/PWR_LED
(Power LED):
Connects to the power status indicator
on the chassis front panel. The LED is on
when the system is operating. The LED is
off when the system is in S3/S4 sleep state
or powered off (S5).
•
HD
(Hard Drive Activity LED):
Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive
is reading or writing data.
•
RES
(Reset Switch):
Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer
if the computer freezes and fails to perform a normal restart.
•
CI
(Chassis Intrusion Header):
Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has
been removed. This function requires a chassis with a chassis intrusion switch/sensor.
•
NC
: No Connection.
Power LED
1
2
19
20
CI-
CI+
PWR_LED-
PWR_LED+
PLED-
PW-
SPEAK+
SPEAK-
PLED+
PW+
Power LED
HD-
RES+
HD+
RES-
Hard Drive
Activity LED
Reset
Switch
Chassis
Intrusion Header
Power Switch
Speaker
PWR_LED-
NC
NC
13) F_USB31C (USB Type-C
™
Header with USB 3.2 Gen 2 Support)
The header conforms to USB 3.2 Gen 2 specification and can provide one USB port.
Pin No.
Definition
Pin No.
Definition
Pin No.
Definition
1
VBUS
8
CC1
15
RX2+
2
TX1+
9
SBU1
16
RX2-
3
TX1-
10
SBU2
17
GND
4
GND
11
VBUS
18
D-
5
RX1+
12
TX2+
19
D+
6
RX1-
13
TX2-
20
CC2
7
VBUS
14
GND
20
10
11
1
- 21 -