Gigabyte Z490 AORUS MASTER WATERFORCE User Manual - Page 75

C-3. Configuring Legacy RAID ROM, MAIN MENU, Create RAID Volume, CSM Support, Enabled

Get Gigabyte Z490 AORUS MASTER WATERFORCE PDF manuals and user guides View all Gigabyte Z490 AORUS MASTER WATERFORCE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

C-3. Configuring Legacy RAID ROM You'll need a discrete graphics card to enter the legacy RAID ROM utility. Enter the Intel® legacy RAID BIOS setup utility to configure a RAID array. Skip this step and proceed with the installation of Windows operating system for a non-RAID configuration. Step 1: In BIOS Setup, go to Boot and set CSM Support to Enabled and Storage Boot Option Control to Legacy. Next, go to Settings\IO Ports\SATA And RST Configuration and make sure USE RST Legacy OROM is set to Enabled. Save the changes and exit BIOS Setup. After the POST memory test begins and before the operating system boot begins, look for a message which says "Press to enter Configuration Utility" (Figure 13). Press + to enter the RAID Configuration Utility. Intel(R) Rapid Storage Technology - Option ROM - 17.8.0.4460 Copyright (C) Intel Corporation. All Rights Reserved. RAID Volumes : None defined. Physical Devices : ID Device Model 1 TOSHIBA DT01ACA1 2 TOSHIBA DT01ACA1 Serial # 763ZLL4FS 763ZM7MFS Size 931.5GB 931.5GB Type/Status(Vol ID) Non-RAID Disk Non-RAID Disk Press to enter Configuration Utility... Figure 13 Step 2: After you press + , the MAIN MENU screen will appear (Figure 14). Create RAID Volume If you want to create a RAID array, select Create RAID Volume in MAIN MENU and press . Intel(R) Rapid Storage Technology - Option ROM - 17.8.0.4460 Copyright (C) Intel Corporation. All Rights Reserved. 1. Create RAID Volume 2. Delete RAID Volume 3. Reset Disks to Non-RAID [ MAIN MENU ] 4. Recovery Volume Options 5. Acceleration Options 6. Exit RAID Volumes : None defined. Physical Deivces : ID Device Model 1 TOSHIBA DT01ACA1 2 TOSHIBA DT01ACA1 [ DISK/VOLUME INFORMATION ] Serial # 763ZLL4FS 763ZM7MFS Size 931.5GB 931.5GB Type/Status(Vol ID) Non-RAID Disk Non-RAID Disk [hi]-Select [ESC]-Exit Figure 14 [ENTER]-Select Menu - 75 - Configuring a RAID Set

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
- 75 -
Configuring a RAID Set
Figure 13
Step 2:
After you press <Ctrl> + <I>, the
MAIN MENU
screen will appear (Figure 14).
Create RAID Volume
If you want to create a RAID array, select
Create RAID Volume
in
MAIN MENU
and press <Enter>.
Figure 14
Intel(R) Rapid Storage Technology - Option ROM - 17.8.0.4460
Copyright (C) Intel Corporation.
All Rights Reserved.
RAID Volumes :
None defined.
Physical Devices :
ID
Device Model
Serial #
Size
Type/Status(Vol ID)
1
TOSHIBA DT01ACA1
763ZLL4FS
931.5GB
Non-RAID Disk
2
TOSHIBA DT01ACA1
763ZM7MFS
931.5GB
Non-RAID Disk
Press
<CTRL - I>
to enter Configuration Utility...
Intel(R) Rapid Storage Technology - Option ROM - 17.8.0.4460
Copyright (C)
Intel Corporation.
All Rights Reserved.
4. Recovery Volume Options
5. Acceleration Options
6. Exit
RAID Volumes :
None defined.
Physical Deivces :
ID
Device Model
Serial #
Size
Type/Status(Vol ID)
1
TOSHIBA DT01ACA1
763ZLL4FS
931.5GB
Non-RAID Disk
2
TOSHIBA DT01ACA1
763ZM7MFS
931.5GB
Non-RAID Disk
[
hi
]-Select
[ESC]-Exit
[ENTER]-Select Menu
[ DISK/VOLUME INFORMATION ]
[ MAIN MENU ]
1. Create RAID Volume
2. Delete RAID Volume
3. Reset Disks to Non-RAID
C-3. Configuring Legacy RAID ROM
You’ll need a discrete graphics card to enter the legacy RAID ROM utility. Enter the Intel
®
legacy RAID BIOS
setup utility to configure a RAID array. Skip this step and proceed with the installation of Windows operating
system for a non-RAID configuration.
Step 1:
In BIOS Setup, go to
Boot
and set
CSM Support
to
Enabled
and
Storage Boot Option Control
to
Legacy
.
Next, go to
Settings\IO Ports\SATAAnd RST Configuration
and make sure
USE RST Legacy OROM
is set to
Enabled
. Save the changes and exit BIOS Setup. After the POST memory test begins and before the operating
system boot begins, look for a message which says "Press <Ctrl-I> to enter Configuration Utility" (Figure 13).
Press <Ctrl> + <I> to enter the RAID Configuration Utility.