Haier HDW100WH User Manual - Page 10

Installation

Get Haier HDW100WH PDF manuals and user guides View all Haier HDW100WH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Installation Positioning the Appliance Position the appliance in the desired location. The back should rest against the wall, and the sides along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or left to allow correct installation. Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink. Use the plastic support that comes with the appliance (see fig .2) and ensure there are no tight bends or kinks. The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water. Levelling the Appliance Once the appliance is positioned, adjust the feet (screwing them in or out) of level the dishwasher. The appliance should not be inclined more than 2 degrees to ensure proper performance. Cold Water Connection Connect the cold water supply hose to a threaded 3/4 bsp connector and make sure that it is fastened tightly (see fig.1). If the water pipes are new or have not been used for an extended period of time, let the water run first, till it is clear and free of impurities. Otherwise the water inlet filter may get blocked. MAX 100 MIN 40 fig.2 Hot Water Connection The appliance can also be connected to the house's hot water supply folloeing the same procedure as for the cold connection. The will reduce the wash cycle time by about 15 minutes and the wash efficiency will be slightly reduced. Attention: The plastic hose support must be fastened to the wall to prevent the drain hose from moving. DO NOT CONNECT TO A PUSH THROUGH HOT WATER SYSTEM OR ONE THAT EXCEEDS A TEMPERATURE OF 60OC. Electrical Connection After making sure that the voltage and frequency in the home correspond to those on the rating plate of the appliance (located on the side of the stainless steel inner door) and that the electrical system can cope with the maximum voltage on the rating plate, insert thr plug into an earthed electrical socket. DO NOT USE ADAPTORS OR EXTENSION LEADS. fig.1 .9. GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
fig.2
Installation
Positioning the Appliance
Position the appliance in the desired location. The back should
rest against the wall, and the sides along the adjacent cabinets
or walls. The dishwasher is equipped with water supply and drain
hoses that can be positioned to the right or left to allow correct
installation.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing them
in or out) of level the dishwasher. The appliance should not be
inclined more than 2 degrees to ensure proper performance.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4 bsp connector
and make sure that it is fastened tightly (see fig.1).
If the water pipes are new or have not been used for an extended
period of time, let the water run first, till it is clear and free of
impurities. Otherwise the water inlet filter may get blocked.
Hot Water Connection
The appliance can also be connected to the house's hot water
supply folloeing the same procedure as for the cold connection.
The will reduce the wash cycle time by about 15 minutes and the
wash efficiency will be slightly reduced.
Attention:
The plastic hose support must be fastened to the wall to pre-
vent the drain hose from moving.
Electrical Connection
After making sure that the voltage and frequency in the home cor-
respond to those on the rating plate of the appliance (located on
the side of the stainless steel inner door) and that the electrical
system can cope with the maximum voltage on the rating plate,
insert thr plug into an earthed electrical socket.
Drain Hose Connection
Insert the drain hose into a drain pipe with a minimum diameter of
40mm, or let it run into the sink. Use the plastic support that comes
with the appliance (see fig .2) and ensure there are no tight bends
or kinks. The free end of the hose must be at a height between 40
and 100 cm and must not be immersed in water.
fig.1
.9.
GB
MAX 100
MIN 40
DO NOT CONNECT TO A PUSH THROUGH HOT WATER
SYSTEM OR ONE THAT EXCEEDS A TEMPERATURE OF
60
O
C.
DO NOT USE ADAPTORS OR EXTENSION LEADS.