Haier L1910A-C User Manual - Page 27

Haier L1910A-C Manual

Get Haier L1910A-C PDF manuals and user guides View all Haier L1910A-C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Troubleshooting Guide To assist in location possible faults use help guide below. Troubleshooting No picture, no sound Verify if the television is properly plugged. Verify if the television is properly supplied power. Verify if electricity is available. Blank screen No sound Poor sound Verify if correct signals are input. Press TV/AV button to change signal input to TV input. Restart the television of power supply is interrupted. Press MUTE button and verify if Mute mode is set. Switch to other channel and verify if the same problem happens. Press VOL+ button to see if the problem can be solved. Verify if sound system is correct. Refer to some chapter for adjust. No picture in some channel Verify if correct channel is selected. Adjust the antenna. Make adjustments by FINE TUNE and MANUAL SEARCH. Verify if the same problem exists in other channels. No color for some channel Check out of picture and sound systems. program (black and white) Refer to relative instructions in the Manual for color adjust. Spots with some or all pictures Verify if the antenna is correctly connected. Verify if the antenna is in good condition. Make fine adjustment of channel. Television out of control Disconnect the television from power supply and, 10 seconds later, connect the television to the power supply. If the problem still exists, contact authorized after-sales service for technical assistance. Note: 1.If the fault can not be repaired using the above guide consult with your local authorized service center. 2.The TV set must only be repaired by a qualified registered service person. Never attempt to remove the back cover as the TV set has dangerous voltages in side that may cause a fatally or fire.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
SETUP
DVD System Setup
DVD System Setup
General Setup Process
1.Press the SETUP button, the
General Setup Page,Preference
Page
will be displayed in turn.
2.Press CH+/- b
to select, the
item, then press
to enter the
submenu.
3.Press CH+/- bu to select
then
press PLAY/ENTER to confirm.
4.Press
EXIT key or press SETUP
repeatedly
to
exit
the
set-up
menus.
or
or
General Setup Page
When using the DVD with the internal TV,
select
.
4
3/LB
The following information applies only
when the DVD output is connected to an
external TV.
(PS = Pan and Scan)
You may select this if you have a normal
aspect ratio (4:3) TV, although the NORMAL
/LB (letter box) is a more common choice. In
PS mode, widescreen material will fill the screen, but at the expense of
chopping off extreme left and right edges of the original film picture. For this
feature to work, the disc must be specially coded. Such discs are uncommon.
(LB = Letter Box)
You may select this if you have a normal aspect ratio (4:3) TV. Widescreen
material will be shown in pure unaltered form, allowing the entire picture area
of the original film to be viewed without any side cropping. Black bars will
appear above and below the picture.
You may select this if you have a widescreen (16:9) TV. Back bars may still
appear above and below the picture even if using a widescreen TV. This is
because some film directors prefer to use ultra widescreen aspect ratios e.g.
2.35:1. This will normally be indicated on the DVD packaging.
4
3/PS
4
3/LB
16
9
ASPECT RATIO DESCRIPTION
..General Setup Page..
Tv Display
4:3 LB
Angle Mark
On
Osd Lang
ENG
Caption
On
Screen Saver
Off
4
3/Ps
4
3/Lb
16
9
.
.
PAL
AUTO
NTSC
..Preference Page..
TV Type
Parental
Password
Default
Auto
..General Setup Page..
4
3/Ps
4
3/Lb
16
9
.
.
TV Display
4:3 LB
Angle Mark
On
OSD Lang
ENG
Caption
On
Screen Saver
Off
PLAY/ENTER
SETUP
PLAY/ENTER