Haier L37K1 User Manual - Page 24

Adjust Menu - tv

Get Haier L37K1 PDF manuals and user guides View all Haier L37K1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Adjust Menu The TV can be used as a display, and you may adjust relevant settings. The operating method of various menus is the same as that described for TV signal. The following are operating methods that different from that for TV signal. When the TV is used as a display, you may set and adjust its picture effect by the following steps. Press TV/AV to switch the signal input to PC mode. 1. Press MENU to display the screen main menu, and then press VOL+/- to select the Adjust menu as shown in the right figure. 2. Press CH+/- to select the option to be adjusted. 3. Press VOL+/- to adjust it. menu OK OK Aspect Ratio Press this key to select the screen display proportion. Auto Adjust This is used to reset the default setting parameters. Clock This is used for adjusting H Position and VPosition as well as relative parameters in PC modes. Phase This is used for adjusting the phase of pixel clock in PC mode. Adjust Vertical and Horizontal position of picture can be adjusted in this item. Precautions: 1. When making H-Size, V-Size, H-Position or V-Position adjustment, there sometimes may be abnormalities in case of a large adjustment range, which is not a fault but for the signal sync out of range, and the picture will become normal by reverse adjustment. 2. In PC mode, there are only two aspect ratios (4:3, full screen) available. 3. There will be a display proportion of "Dot By Dot" when the singal is 50Hz in the source of YPbPr or HDMI.This proportion is for Full-HD panel test in factory.Plseae do not use this proportion,otherwise the display will be distortionary.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Adjust Menu
Aspect Ratio
Press this key to select the screen display proportion.
Auto Adjust
This is used to reset the default setting parameters.
Clock
This is used for adjusting H Position and V Position as well
as relative parameters in
PC
modes.
Phase
This is used for adjusting the phase of pixel clock
in PC mode.
Adjust
Vertical
and Horizontal position of picture can be adjusted in this
item.
menu
OK
OK
The TV can be used as a display, and you may adjust relevant settings. The operating method of
various menus is the same as that described for TV signal. The following are operating methods that
different from that for TV signal.
When the TV is used as a display, you may set and adjust its
picture effect by the following steps.
Press TV/AV to switch the signal input to PC mode.
1. Press MENU to display the screen main menu, and then press
VOL+/- to select the Adjust menu as shown in the right figure.
2. Press CH+/- to select the option to be adjusted.
3. Press VOL+/- to adjust it.
Precautions:
1. When making H-Size, V-Size, H-Position or V-Position adjustment, there sometimes may be
abnormalities in case of a large adjustment range, which is not a fault but for the signal sync out of
range, and the picture will become normal by reverse adjustment.
2. In PC mode, there are only two aspect ratios (4:3, full screen) available.
3. There will be a display proportion of "Dot By Dot" when the singal is 50Hz in the source of
YPbPr or HDMI.This proportion is for Full-HD panel test in factory.Plseae do not use this
proportion,otherwise the display will be distortionary.