Haier SPW1200P User Manual - Page 23

Unpacking Your Washer, Leveling Your Washer, Steps for Installation

Get Haier SPW1200P PDF manuals and user guides View all Haier SPW1200P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

English Unpacking Your Washer • Remove all packing materials. This includes the foam base and all adhesive tape holding the washer accessories inside and outside. Slide out and remove bottom styrofoam that is used to secure the washer from shipping damage due to vibration and shock. • Inspect and remove any remains of packing, tape or printed materials before using the washer. Leveling Your Washer • Your washer has 4 leveling legs; which are located on the four bottom corners. After properly placing your washer in its final position, you can level your washer. • Leveling legs can be adjusted by turning them counterclockwise to raise your washer or turning them clockwise to lower your washer. Steps for Installation Installation Pre-Requirement: • Select a suitable location for the washer on a hard even surface away from direct sunlight or heat source e.g. radiators, baseboard heaters, cooking appliances etc. • Any floor unevenness should be corrected with the leveling legs located on the bottom corners of the washer. • The washer must be placed at room temperature. You must not place washer where the temperature is at below freezing. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
English
22
Unpacking Your Washer
• Remove all packing materials. This includes the foam base and all adhesive tape
holding the washer accessories inside and outside. Slide out and remove bottom
styrofoam that is used to secure the washer from shipping damage due to
vibration and shock.
• Inspect and remove any remains of packing, tape or printed materials before
using the washer.
Leveling Your Washer
• Your washer has 4 leveling legs; which are located on the four
bottom corners.
After properly placing your washer in its final position, you can level your washer.
• Leveling legs can be adjusted by turning them counterclockwise to raise your
washer or turning them clockwise to lower your washer.
Steps for Installation
Installation Pre-Requirement:
• Select a suitable location for the washer on a hard even surface away from direct
sunlight or heat source e.g. radiators, baseboard heaters, cooking appliances etc.
• Any floor unevenness should be corrected with the leveling legs located on the
bottom corners of the washer.
• The washer must be placed at room temperature. You must not place washer
where the temperature is at below freezing.