Haier WQP12-CFESS User Manual - Page 4

Starting the Appliance Starting a wash cycle After having completed all of the installation steps in the preceding paragraphs, turn on the water to the unit, partially open the door of the dishwasher, and press the ON-OFF button "A" located on the control panel. The "B" indicator light will come on. At this point, the appliance is on and ready to be programmed. Setting and Starting a wash Cycle Choose the desired cycle by pressing the cycle selection button "G". Each time it is pressed, the cycle indicator lights "F" will change to indicate the cycle selected. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual, especially when first using the appliance). Close the door and after a few seconds, The wash cycle will begin. Read the paragraph entitled, "Cancelling or changing a cycle while underway. "The end of the cycle will be signalled by six beeps, and the indicator light "F" will extinguish. Cancelling or changing a cycle while underway... Premise: A cycle that is underway can only be changed if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). To change the cycle currently underway, open the door, press the "G" programming button and hold it in for about 5 seconds. Once the cycle has been cancelled, the dishwasher will emit a short acoustic sound and the relative indicator light will turn off. To set a new wash cycle, follow the instructions contained in the paragraph entitled, "Setting and Starting a Wash Cycle." At the end of the wash cycle... Six beeps will indicate that the wash cycle has finished and the cycle indicator light "F" will begin to extinguish. Open the door, turn off the appliance using the ON/OFF switch and turn off the water supply to the unit. Wait a few minutes before removing the dishes so as to avoid handling them while still hot (when they are more susceptible to breakage) and to get better drying results. Setting The Start Delay Time Open the door of the dishwasher partially. Press button "J" (see, Close-up View" Control Panel") to delay the starting time for a wash cycle. .1st press, "2h" indicator comes on, the cycle will start in 2 hours. .2nd press, "4h" light indicator comes on, the cycle will start in 4 hours. .3rd press, "6h" light indicator comes on, the cycle will start in 6 hours. .4th press, "2h" and "6h" light indicators come on, the cycle will start in 8 hours. .5th press, "4h" and "6h" light indicators come on, the cycle will start in 10 hours. .6th press, "2h" , "4h" and "6h" light indicators come on, the cycle will start in 12 hours. .last press, all light indicators will extinguish and you can reset. After selecting the delay time, the wash cycle can be set, as explained in "Starting a wash cycle..." There will be a short acoustic signal, and at this point the delay period will begin to count down. During this period the delay indicator light (I) will blink. At the end of the delay time, the indicator will stop blinking and the cycle will start. NOTE: a) During the delay period, none of the settings can be modified. If necessary, they can be cancelled by pressing cycle selector "P" for about 5 seconds. b) If the power to the appliance goes off or the door is opened during the delay period, the clock will stop the countdown. It will start again when the power has come back on, or when the door has been closed. Wash Cycle Adjustment Buttons 1/2 Load Button This button (see" Close-up View-Control Panel", letter "C") makes it possible to wash dishes using only the upper rack if there are not enough dishes for a full load, This will allow you to save on water and electrical energy. It cannot be used with the heavy duty wash cycles. .5. Wash Cycle Table Cycle Cycle Selection Information Description of Cycle Heavy Duty (IEC-EN50242) Very dirty dishes, pots and pans. (Not to be used with delicate items) Normal Wash Normal dirty dishes, pots and pans. Standard daily cycle. Light Wash Normal dirty dishes, pots and pans without dried on residue. Pre-wash with cold water. Extended wash at 56 Rinse with cold water. Rinse with hot water Drying. Pre-wash with cold water. Extended wash at 56 . Rinse with cold water. Rinse with cold water. Rinse with hot water. Drying. Pre-wash with cold water. Extended wash at 56 Rinse with cold water. Rinse with hot water Drying. Glassware Economic, fast cycle to be used for delicate items which are sensitive to higher. Run immediately after dishes are used. Wash at 58 . Rinse with warm water. Hot rinse. Drying. Rapid Wash Rinse Economic, fast cycle to be used to on not very dirty dishes right after they are used. No drying cycle. Pre-wash of dishes, pots and pans while waiting for the load to be completed after the subsequent meal. Short wash at 40 . Cold rinse. Short cold wash to prevent food residue from drying on the dishes Heat wash The cycle of heat washing and dry tableware. Heat washing. .6. Detergent Rinse Aid 30g 30g 30g 15g 15g