Harbor Freight Tools 35570 User Manual
Harbor Freight Tools 35570 - 1/2 HP Mortising Machine Manual
 |
View all Harbor Freight Tools 35570 manuals
Add to My Manuals
Save this manual to your list of manuals |
Harbor Freight Tools 35570 manual content summary:
- Harbor Freight Tools 35570 | User Manual - Page 1
in serious injury. SAVE THIS MANUAL. Copyright© 1996 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, - Harbor Freight Tools 35570 | User Manual - Page 2
Base Overall Weight 1/2 HP, 2.3 Amps @ 110 V, 60Hz 3580 RPM 5" 5" 13-3/8" x 6" 10" x 7-3/4" 54 lbs. SAVE THIS MANUAL You will need this manual for the safety instructions, assembly instructions, operating procedures, parts list, and diagram. Put them in a safe, dry place for future reference - Harbor Freight Tools 35570 | User Manual - Page 3
operation. Any part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in the instruction manual. Have defective switches replaced by an authorized service center. Don't use the tool if switch does not turn on and off properly - Harbor Freight Tools 35570 | User Manual - Page 4
below is used to determine the rating required according to the length of the cord(s). The amps of your tool are found either in this manual, or on the nameplate of the tool. CORD(S) LENGTH (FEET) 25 50 75 100 125 150 175 200 WIRE GAUGE REQUIRED 18 18 16 16 - Harbor Freight Tools 35570 | User Manual - Page 5
Three chisels and mortising bits (1/4", 3/8", & 1/2") 14. Chuck Key (47) ASSEMBLY INSTRUCTIONS 1. Slide handle (24) into the receiver hole on the right side of the & non-flammable solvent, clean the rust inhibitor from the base (3), guide column (16), gear column, gear casing(23), and all other - Harbor Freight Tools 35570 | User Manual - Page 6
4. Slide the bit into the chisel. 5. Insert the chisel into the bushing (38) and the bit into the chuck. Make sure the chisel's slot is facing either the right or left to provide for proper chip ejection. 6. Make sure there is at least 3/32"-7/32"o f bit protruding from the end of the chisel, then - Harbor Freight Tools 35570 | User Manual - Page 7
MAINTENANCE Bit and Chisel Sharpening: If the bit is dull, it can break the chisel, resulting in operator injury. It is sharpenable, however, if there is any sign of wear along the twist (such as irregular grooves or hollows) the bit must be replaced. Chisels cannot be sharpened if the walls become - Harbor Freight Tools 35570 | User Manual - Page 8
Problem ‡:LOOQRWVWDUW ‡0DFKLQHVWDUWV EXWELWGRHV QRWPRYH ‡2SHUDWLRQ LQWHUUXSWHG ‡%URNHQ&KLVHOV ‡&KLSVFORJJHGLQ &KLVHO ‡TRUQRUURXJK PRUWLVHV TROUBLE SHOOTING &DXVH ‡1RWSOXJJHGLQ ‡)XVHRUFLUFXLWEORZQ ‡6RFNHWGRHVQRWIXQFWLRQ ‡'DPDJHGFRUGRUSOXJ ‡6ZLWFKQRW - Harbor Freight Tools 35570 | User Manual - Page 9
Washer 11 Bracket B 12 Knob 12A Handle 13 Spring 15 Gear Column 16 Guide Column 17 Knob 18 Depth Set Guide 19 Set Screw 20 Gear Shaft 21 Gear 22 Gear Access Plate 23 Gear Casing 24 Handle 25 Guide Sleeve PARTS LIST 26 Stop Plate 27 Washer 28 Bolt - Harbor Freight Tools 35570 | User Manual - Page 10
42 43 44 45 40 PARTS DIAGRAM 29-01 29-02 29-03 29-04 46 12A 47 48 49 SKU 35570 Page 10 - Harbor Freight Tools 35570 | User Manual - Page 11
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of ninety days from the date of
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
 |
 |
MORTISING MACHINE
MODEL
35570
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVETHIS MANUAL.
Copyright
©
1996 by Harbor Freight Tools
®
.
All rights reserved.
No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual
product may differ slightly from the product described herein. Tools required for assembly and service may not
be included.
For technical questions or replacement parts, please call 1-800-444-3353.