Harbor Freight Tools 63157 User Manual
Harbor Freight Tools 63157 - 18 Gauge Brad Air Nailer Manual
 |
View all Harbor Freight Tools 63157 manuals
Add to My Manuals
Save this manual to your list of manuals |
Harbor Freight Tools 63157 manual content summary:
- Harbor Freight Tools 63157 | User Manual - Page 1
manual and the receipt in a safe and dry place for future reference. REV 16e Visit our website at: http://www.harborfreight.com Email our technical support slightly from the product described herein. Tools required for assembly and service may not be included. Read this material before using this - Harbor Freight Tools 63157 | User Manual - Page 2
with side shields. Symbol Property or statement Warning marking concerning Risk of Puncture Injury. Wear heavy‑duty work gloves. Read the manual before set-up and/or use. WARNING marking concerning Risk of Hearing Loss. Wear hearing protection. WARNING marking concerning Risk of Respiratory - Harbor Freight Tools 63157 | User Manual - Page 3
should always be followed, including the following: General To reduce the risks of electric shock, fire, and injury to persons, read all the instructions before using the tool. Work Area a. Keep the work area clean and well lighted. Cluttered benches and dark areas increase the risks of electric - Harbor Freight Tools 63157 | User Manual - Page 4
way to secure and support the workpiece to 's operation. If damaged, have the tool serviced before using. Many accidents are caused by fasteners listed in the Specifications chart of this manual. Fasteners not identified for use with this tool INSTRUCTIONS. Operation Maintenance Page 4 For technical questions, - Harbor Freight Tools 63157 | User Manual - Page 5
make any modifications to this tool. 14. Refer to the tool maintenance instructions for detailed information on the proper maintenance of the tool. 15. Fire prevent falls from bystanders accidentally pulling on it. 22. Obey the manual for the air compressor used to power this tool. 23. Install - Harbor Freight Tools 63157 | User Manual - Page 6
a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or , maintain tool as explained in this manual. If abnormal vibration occurs, stop immediately. SAVE THESE INSTRUCTIONS. Setup Operation Maintenance Page 6 For - Harbor Freight Tools 63157 | User Manual - Page 7
Safety Functional Description Specifications Maximum Air Pressure Air Inlet Air Consumption Safety Mechanism Type Nail Type 110 PSI 1/4″ - 18 NPT 0.5 CFM @ 90 PSI Single Sequential 18 Gauge 5/8″ - 2″ Brad Setup Operation Maintenance Item 63157 For technical questions, please call 1-888-866- - Harbor Freight Tools 63157 | User Manual - Page 8
Safety Components and Controls Air Deflector Air Inlet Plug Trigger Depth Knob Latch Quick Release Lever Safety Nosepiece Safety Nosepiece - Also called the workpiece contact, the Safety Nosepiece helps prevent the tool from firing unless it is pressed against an object. Setup Operation - Harbor Freight Tools 63157 | User Manual - Page 9
following pages, refer to the Assembly Diagram near the end of this manual. Air Supply TO PREVENT EXPLOSION: Use only clean, dry, regulated, regulator with pressure gauge, oiler, in-line shutoff valve, and quick coupler for best service, as shown on Figure A on page 10 and Figure B on page 11. An - Harbor Freight Tools 63157 | User Manual - Page 10
Safety Setup Operation Maintenance Page 10 Figure A: Portable Air Supply Setup Lubricated Tools Bc D A E F A For technical questions, please call 1-888-866-5797. Non-lubricated Tools B Description A Air Hose B Filter C Regulator D Lubricator (optional) E Coupler and Plug F Leader Hose ( - Harbor Freight Tools 63157 | User Manual - Page 11
Figure B: Stationary Air Supply Setup Item 63157 Slope Lubricated G Tools c J K H L M F cD E For technical questions, please call 1-888-866-5797. I IN B A B A F c J F Non-lubricated Tools LO H Description A Vibration Pads B Anchor Bolts C Ball Valve D Isolation Hose E Main - Harbor Freight Tools 63157 | User Manual - Page 12
Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems qualified service technician. - Harbor Freight Tools 63157 | User Manual - Page 13
the strip flat on the bed of Magazine. 3. Slide strip forward into Drive Guide (62). 4. Gently push the Sliding Magazine inward and push forward until the indicating 15 pieces and 5-piece marker increments thereafter. General Operating Instructions 1. Before each use, test the tool as directed in - Harbor Freight Tools 63157 | User Manual - Page 14
Instructions Procedures not specifically explained in this manual any fasteners. • Empty the magazine and leave it open during service. The Magazine is spring‑loaded and may cause parts or a or leaking air is detected, have the problem corrected before further use. TO PREVENT EXPLOSION: - Harbor Freight Tools 63157 | User Manual - Page 15
of firing any fasteners. • Empty the magazine and leave it open during service. The Magazine is spring‑loaded and may cause parts or a fastener to fly ; pliers may be necessary to remove a stuck fastener. 6. Inspect the Drive Guide for any bends or breakage. If it is damaged, do not use the - Harbor Freight Tools 63157 | User Manual - Page 16
Troubleshooting Problem Insufficient pressure (PSI). 1. Clear jammed fastener according to Clearing Jams instructions. 2. Reload with correct fasteners. 3. Empty, then reload precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. Operation Maintenance Page - Harbor Freight Tools 63157 | User Manual - Page 17
Safety PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS - Harbor Freight Tools 63157 | User Manual - Page 18
Nosepiece 55 Safety Nosepiece Set 56 Quick Release Spring 57 Quick Release Lever 58 Drive Guide Cover 59 Pin 60 Pin 61 Screw M4*18 62 Drive Guide 63 Spacer 64 Nut M5 65 Screw 4*12 66 Magazine Support 67 Fixed Magazine 68 Steel Bar Φ2.16*170 69 Latch 70 Torsion Spring 71 - Harbor Freight Tools 63157 | User Manual - Page 19
Assembly Diagram Safety 1 2 3 4 5 6 7 8 9 10 11 13 14 12 15 16 17 19 18 20 21 23 22 24 25 26 27 Setup Operation 78 45 44 43 28 64 81 29 46 30 31 32 33 34 38 35 36 37 80 40 39 41 42 49 50 51 52 47 48 63 6 53 55 54 27 57 82 56 60 59 58 62 61 77 76 75 74 73 6 65 66 67 79 68 - Harbor Freight Tools 63157 | User Manual - Page 20
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Owner’s Manual & Safety Instructions
Save This Manual
Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures.
Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged.
If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright
©
2016 by Harbor Freight Tools
®
.
All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally.
Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
REV 16e