Harbor Freight Tools 67450 User Manual

Harbor Freight Tools 67450 - 11 Gauge Coil Roofing Nailer Manual

Get Harbor Freight Tools 67450 - 11 Gauge Coil Roofing Nailer PDF manuals and user guides View all Harbor Freight Tools 67450 manuals
Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 67450 manual content summary:

  • Harbor Freight Tools 67450 | User Manual - Page 1
  • Harbor Freight Tools 67450 | User Manual - Page 2
    with side shields. Symbol Property or statement Warning marking concerning Risk of Puncture Injury. Wear heavy‑duty work gloves. Read the manual before set-up and/or use. WARNING marking concerning Risk of Hearing Loss. Wear hearing protection. WARNING marking concerning Risk of Respiratory
  • Harbor Freight Tools 67450 | User Manual - Page 3
    should always be followed, including the following: General To reduce the risks of electric shock, fire, and injury to persons, read all the instructions before using the tool. Work area a. Keep the work area clean and well lighted. Cluttered benches and dark areas increase the risks of electric
  • Harbor Freight Tools 67450 | User Manual - Page 4
    way to secure and support the workpiece to 's operation. If damaged, have the tool serviced before using. Many accidents are caused by fasteners listed in the Specifications chart of this manual. Fasteners not identified for use with this tool INSTRUCTIONS. OPERATION MAINTENANCE Page 4 For technical questions,
  • Harbor Freight Tools 67450 | User Manual - Page 5
    make any modifications to this tool. 14. Refer to the tool maintenance instructions for detailed information on the proper maintenance of the tool. 15. Fire prevent falls from bystanders accidentally pulling on it. 22. Obey the manual for the air compressor used to power this tool. 23. Install
  • Harbor Freight Tools 67450 | User Manual - Page 6
    have regular medical check-ups to ensure medical problems are not being caused or worsened from use vibration, maintain tool as explained in this manual. If abnormal vibration occurs, stop immediately. on roofs. SAVE THESE INSTRUCTIONS. SETUP OPERATION MAINTENANCE Page 6 For technical
  • Harbor Freight Tools 67450 | User Manual - Page 7
    0.120″ Diameter Shank, 3/4″ ~ 1-3/4″ Long Components and Controls Exhaust Trigger Air Inlet SETUP OPERATION MAINTENANCE Safety Nosepiece Latch Magazine Shingle Guide Safety Nosepiece - Also called the workpiece contact, the Safety Nosepiece helps prevent the tool from firing unless it is
  • Harbor Freight Tools 67450 | User Manual - Page 8
    pages, refer to the Assembly Diagram near the end of this manual. Trigger Installation TO PREVENT SERIOUS INJURY FROM ACCIDENTAL FIRING: Disconnect for proper operation and test safety operation according to the instructions that follow. Figure B: Spring Position OPERATION MAINTENANCE Page 8
  • Harbor Freight Tools 67450 | User Manual - Page 9
    bottled gas as a power source for this tool. 1. Incorporate a filter, regulator with pressure gauge, oiler, in-line shutoff valve, and quick coupler for best service, as shown on Figure E on page 10 and Figure F on page 11. An in-line shutoff ball valve is an important safety device because it
  • Harbor Freight Tools 67450 | User Manual - Page 10
    SAFETY SETUP OPERATION MAINTENANCE Page 10 Figure E: Portable Air Supply Setup Lubricated Tools BC D A E F A For technical questions, please call 1-800-444-3353. Non-lubricated Tools B Description A Air Hose B Filter C Regulator D Lubricator (optional) E Coupler and Plug F Leader Hose (
  • Harbor Freight Tools 67450 | User Manual - Page 11
    Figure F: Stationary Air Supply Setup Item 67450 For technical questions, please call 1-800-444-3353. Slope Lubricated G Tools C J K H L M F CD E I IN B A B A F C J F Non-lubricated Tools LO H Description A Vibration Pads B Anchor Bolts C Ball Valve D Isolation Hose E Main
  • Harbor Freight Tools 67450 | User Manual - Page 12
    Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems qualified service technician.
  • Harbor Freight Tools 67450 | User Manual - Page 13
    workpiece without pulling the Trigger. The tool must not cycle (fire). If it cycles (fires), stop immediately and have it repaired by a qualified service technician. 6. Hold the tool away, or off of the workpiece. The Safety Nosepiece should return to its original position. Squeeze the Trigger. The
  • Harbor Freight Tools 67450 | User Manual - Page 14
    SAFETY Loading the Tool TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION, BEFORE LOADING: • Wear ANSI-approved safety goggles with side shields. Other people in the work area must also wear ANSI-approved impact safety goggles with side shields. • Release the trigger. • Detach the air supply. •
  • Harbor Freight Tools 67450 | User Manual - Page 15
    Instructions 1. Before each use, test the tool as directed in the prior section. 2. If an automatic oiler is not used, add a few drops of Pneumatic Tool Oil to the airline connection before use. Add a few drops more after each hour of continual use. 3. Shingle Guide Setup: The Shingle Guide
  • Harbor Freight Tools 67450 | User Manual - Page 16
    Instructions Procedures not specifically explained in this manual or leaking air is detected, have the problem corrected before further use. TO PREVENT EXPLOSION: the jam cannot be cleared using the method above, have the tool serviced by a qualified technician. Note: Keep tool free of tar and
  • Harbor Freight Tools 67450 | User Manual - Page 17
    Troubleshooting Problem Insufficient pressure (PSI). 1. Clear jammed fastener according to Clearing Jams instructions. 2. Reload with correct fasteners. 3. Empty, then reload precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. OPERATION MAINTENANCE Item
  • Harbor Freight Tools 67450 | User Manual - Page 18
    THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE 37 Spring Pin 38 Safe Bracket Guide 39 Trigger Valve Guide 40 O-Ring 12.8x1.9 41 O-Ring 14. Screw 75 Nut 76 Washer 77 Connecting Plate 78 Support 79 Bracket 80 Screw 81 Screw 82 Nail Canister
  • Harbor Freight Tools 67450 | User Manual - Page 19
    Assembly Diagram SAFETY SETUP OPERATION MAINTENANCE Record Product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement
  • Harbor Freight Tools 67450 | User Manual - Page 20
    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20