Harman Kardon AVR 130 Owners Manual - Page 21

OPERATION Basic Operation Once you have completed the setup and configuration of the AVR 130, it is simple to operate and enjoy. The following instructions will help you maximize the enjoyment of your new receiver: Turning the AVR 130 On or Off • When using the AVR 130 for the first time, you must press the Main Power Switch 1 on the front panel to turn the unit on. This places the unit in a Standby mode, as indicated by the amber color of the Power Indicator 2. Once the unit is in Standby, you may begin a listening session by pressing the Standby/On Switch 3 on the front panel or the AVR Selector f. Note that the Power Indicator 2 will turn blue. This will turn the unit on and return it to the input source that was last used. The unit may also be turned on from Standby by pressing any of the Input Selector Buttons eg 39 on the remote or the Input Source Selector ^ on the front panel. NOTE: After pressing one of the Input Selector Buttons eg 39 to turn the unit on, press the AVR Selector f to set the remote control to the AVR 130's functions. To turn the unit off at the end of a listening session, simply press the Standby/On Switch 3 on the front panel or the Power Off Button a on the remote. Power will be shut off to any equipment plugged into the rear-panel Switched AC Outlet ⁄ and the Power Indicator 2 will turn amber. When the remote is used to turn the unit "off" it is actually placing the system in a Standby mode, as indicated by the amber color of the Power Indicator 2. • To program the AVR 130 for automatic turn-off, press the Sleep Button j on the remote. Each press of the button will decrease the time before shut- down in the following sequence, as shown in the Lower Display Line ¯: 90 80 70 60 50 min min min min min 40 min 30 min 20 min 10 min OFF When the programmed sleep time has elapsed, the unit will automatically turn off. Note that the front panel indicators and displays will dim to one-half brightness when the Sleep function is programmed. To cancel the Sleep function, press the Sleep Buttonj as many times as needed for the Lower Display Line ¯ to display the SLEEP OFF message, at which time the front panel displays will return to normal brightness.. When you will be away from home for an extended period of time it is always a good idea to completely turn the unit off with the front-panel Main Power Switch 1. NOTE: All preset memories are lost if the unit is left turned off by using the Main Power Switch 1 for more than four weeks. Source Selection • To select a source, press any of the Source Selector Buttons eg 39 on the remote. • The input source may also be changed by pressing the front-panel Input Source Selector ^. Each press of the button will move the input selection through the list of available inputs. • As the input is changed, the AVR 130 will automatically switch to the digital input (if selected), surround mode, output levels and night mode status that were entered during the configuration process for that source, as well as any speaker settings established by using the INDIVIDUAL Bass Management setting. • The front-panel Video 3 Inputs Ô may be used to connect your cable television converter or satellite receiver, or you may connect a device such as a video game or camcorder to your home entertainment system on a temporary basis. • When the input is changed to one with a digital audio source, the Lower Display Line ¯ will temporarily display detailed information regarding the bitstream data for the source in use. For PCM sources, the message will show the bit rate, while for Dolby Digital and DTS sources the display will show the channel information data for the number of front/surround/LFE channels present in the incoming data. • When an audio source is selected, the last video input used remains routed to the Video 1 Audio/ Video e and S-Video Outputs °. This allows you to listen to an audio input such as the tuner while watching one of the video inputs. This also allows you to choose a video source and then seelct the 6Channel Direct Input a as the audio source. • When a Video source is selected, the video signal for that input will be routed to the Video Monitor b and S-Video Monitor fi Outputs, as well as to the Video 1 Audio/Video e and S-Video Outputs ° and will be viewable on a TV monitor connected to the AVR 130. Volume Control • Adjust the volume to a comfortable level using the front-panel Volume Control Ù or remote Volume Up/Down 37 buttons. • When listening in one of the Stereo modes with the surround circuits off, the Balance Control Ò may be used to adjust the relative sound output between the front left and right speakers. For all other modes it is important that the Balance Control remain in the "12 o'clock" position in order to assure a proper sound field presentation. • To temporarily silence all speaker outputs press the Mute Button 40 . This will interrupt the output to all speakers and the headphone jack, but it will not affect any recording or dubbing that may be in progress. Press the Mute Button 40 again or adjust the volume to return to normal operation. • During a listening session you may wish to adjust the Bass Control Ó and Treble Control Ú to suit your listening tastes or room acoustics. • To set the output of the AVR 130 so that the output is "flat," with the tone controls deactivated, press the Tone Mode Button 5 until the words Tone Out appear momentarily in the Lower Display Line ¯. To return the tone controls to an active condition, press the Tone Mode Button 5 until the words Tone In momentarily appear in the Lower Display Line ¯. • For private listening, plug the 1/4" stereo phone plug from a pair of stereo headphones into the front panel Headphone Jack 4. Note that when the headphone's plug is connected, the word HEADPHONE IN will scroll once across the Lower Display Line ¯ and all speakers will be silenced. When the headphone plug is removed, the audio feed to the speakers will be restored. OPERATION 21