Harman Kardon AVR 1565 Quick Start Guide - Page 7
Assign the Digital Audio Connectors, General Specifications - review
View all Harman Kardon AVR 1565 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
AVR 1565/AVR 1566 Connections Use the remote's left and right arrow buttons to select "On" or "Off" for each speaker position, depending on which speakers you have connected to the receiver. When you're finished, select "Back To Master Menu." For now you can skip the "Sub Mode" and "Crossover" settings. For complete details about making these settings, please download the AVR 1565/AVR 1566 Owner's Manual from www.harmankardon.com. 5. Measure the distance from each speaker in your system to the listening position. Write down the distances. 6. Select "Distance." The Distance menu will appear. * DISTANCE * FL : 10FT CEN : 10FT FR : 10FT SR : 10FT SL : 10FT SUB : 10FT DELAY RESET : OFF UNIT : FEET A/V SYNC DELAY : 0mS BACK TO SPEAKER SETUP Use the remote's left and right arrow buttons to change the distance setting on the screen for each speaker so it matches the distance you measured. Note: If you want, you can change the units from feet to meters by selecting "Unit" and pressing the right arrow button. When you're finished, select "Back To Speaker Setup." 7. Select "Level." The Level Adjust menu will appear. * LEVEL ADJUST* FL : 0dB CEN: 0dB FR : 0dB SR : 0dB SL : 0dB SUB: 0dB CHANNEL RESET: OFF TEST TONE SEQ: MANUAL TEST TONE : OFF BACK TO SPEAKER SETUP Use the remote's down arrow button to select "Test Tone" and press the right arrow button to set "Test Tone" to ON. You will hear test noise through the front left speaker. 8. S it in the main listening position and note the volume of the test noise through the first speaker. Press the remote's down arrow button to advance the test noise to each of your system's speakers and note the volume level of the noise in each speaker. 9. As you advance the test noise through the speakers, use the remote's left and right arrow buttons to adjust the volumes of the channels until all of them play at the same volume. When you're finished, press the remote's OSD button to turn off the on-screen menus. Assign the Digital Audio Connectors 1.Review the input connections you listed on the Input Connections and Source Buttons table, on page 4. Note which source devices you connected to the digital audio connectors. (If you did not connect any source devices to the digital audio connectors, you can skip this section.) 2. Turn on your TV and select the TV input where you connected the AVR in Connect Your TV or Video Display, on page 3. 3. Press the remote control's OSD button. The AVR's on-screen display (OSD) Master Menu will appear on the TV. ** MASTER MENU ** INPUT SETUP SURROUND SELECT SPEAKER SETUP SYSTEM SETUP 4. Use the remote's arrow and OK buttons to select "Input Setup." The Input Setup menu will appear. * INPUT SETUP * SOURCE : DVD TITLE: AUDIO IN : ANALOG AUTO POLL : OFF BXR : OFF TONE : IN BASS : 0 TREBLE : 0 BACK TO MASTER MENU 5. For each source device you connected to a digital audio input: a) U se the remote's up and down arrow buttons to select "Source." Use the left and right arrow buttons to change the listed source to one of the sources you connected to a digital audio input. b) Use the remote's down arrow button to select "Audio In." * INPUT SETUP * SOURCE : DVD TITLE: AUDIO IN : OPT 1 AUTO POLL : ON BXR : OFF TONE : IN BASS : 0 TREBLE : 0 BACK TO MASTER MENU c) U se the remote's left and right arrow buttons to select the digital audio input where you connected the source device. When you're finished, press the remote's OSD button to turn off the on-screen menu. You are now ready to enjoy your AVR! IMPORTANT: For complete information about using all of your audio/video receiver's features and capabilities, download the AVR 1565/AVR 1566 Owner's Manual from www.harmankardon.com. General Specifications Power consumption: