Harman Kardon AVR 1710 Quick Start Guide - Page 8

AVR Setup - remote setup

Get Harman Kardon AVR 1710 PDF manuals and user guides View all Harman Kardon AVR 1710 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

AVR AVR Setup Set Up the AVR Install the Batteries in the Remote Control Remove the remote control's battery cover, insert the two supplied AAA batteries as shown in the illustration, and replace the battery cover. 1. Remove 2. Insert 3. Replace Cover Batteries Cover Configure the AVR for Your Speakers: AVR 1710/AVR 171/AVR 1610/AVR 161 Note: The on-screen menus shown in this guide may differ slightly from your AVR's actual menu screens. Before you use your AVR you need to configure it to work with your particular speaker system. Your AVR's EZSet/EQ™ Plus system uses the supplied EzSet/EQ microphone to detect the capabilities of each connected speaker and optimize the AVR's performance for them automatically. Before beginning, be sure you have correctly connected your speakers to the AVR. 1. P lug the supplied EzSet/EQ™ microphone into the AVR's Headphone connector. AVR Headphone Connector NOTE: Remove the protective plastic from the AVR's front panel so it doesn't reduce the remote control's effectiveness. Using the Remote Control You will be using the following remote-control buttons to configure your AVR: OSD/Menu Button Left/Right/Up/Down Buttons AVR OK Button Button Turn On the AVR Press the front-panel Power button. Power Button Back/Exit Button EzSet Microphone (supplied) 2. Place the microphone at ear height in your listening position. 3. Turn on your TV and select the TV input where you connected the AVR in Connect Your TV or Video Display, on page 4. 4. Press the remote control's AVR button, then press the OSD/Menu button. The AVR's on-screen display (OSD) setup menu will appear on the TV. (Note: If you have used a composite video connection to your TV, the OSD menus will not appear on your TV. Follow the steps below using the AVR's front-panel display.) MASTER MENU Source Select Source Setup Surround Mode Speaker Setup Zone2 Network System Setup 5. Use the remote's arrow and OK buttons to select "Speaker Setup." Speaker Setup Auto: EZ Set/EQ Manual Setup 6. Select "Auto: EZ Set/EQ." 7. Select "Continue." 8. Follow the instructions that appear on the screens. Remain quiet while the test noise 8 plays through the speakers.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
AVR
8
AVR Setup
Set Up the AVR
Install the Batteries in the Remote Control
Remove the remote control’s battery cover, insert the two supplied AAA batteries as shown in
the illustration, and replace the battery cover.
1. Remove
Cover
2. Insert
Batteries
3. Replace
Cover
NOTE: Remove the protective plastic from the AVR’s front panel so it doesn’t reduce the
remote control’s effectiveness.
Using the Remote Control
You will be using the following remote-control buttons to configure your AVR:
Left/Right/Up/Down
Buttons
Back/Exit
Button
AVR
Button
OK
Button
OSD/Menu
Button
Turn On the AVR
Press the front-panel Power button.
Power Button
Configure the AVR for Your Speakers:
AVR 1710/AVR 171/AVR 1610/AVR 161
Note: The on-screen menus shown in this guide may differ slightly from your AVR’s actual
menu screens.
Before you use your AVR you need to configure it to work with your particular speaker
system. Your AVR’s EZSet/EQ
™
Plus system uses the supplied EzSet/EQ microphone to
detect the capabilities of each connected speaker and optimize the AVR’s performance
for them automatically. Before beginning, be sure you have correctly connected your
speakers to the AVR.
1. Plug the supplied EzSet/EQ
™
microphone into the AVR’s Headphone connector.
AVR Headphone Connector
EzSet Microphone (supplied)
2. Place the microphone at ear height in your listening position.
3. Turn on your TV and select the TV input where you connected the AVR in
Connect Your
TV or Video Display,
on page 4.
4. Press the remote control’s AVR button, then press the OSD/Menu button. The AVR’s
on-screen display (OSD) setup menu will appear on the TV. (Note: If you have used
a composite video connection to your TV, the OSD menus will not appear on your TV.
Follow the steps below using the AVR’s front-panel display.)
MASTER MENU
Source Select
Source Setup
Surround Mode
Speaker Setup
Zone2
Network
System Setup
5. Use the remote’s arrow and OK buttons to select “Speaker Setup.”
Speaker Setup
Auto: EZ Set/EQ
Manual Setup
6. Select “Auto: EZ Set/EQ.”
7. Select “Continue.”
8. Follow the instructions that appear on the screens. Remain quiet while the test noise
plays through the speakers.