Harman Kardon AVR45 Owners Manual - Page 16

Remote Control Functions 13 n Memory Button: Press this button to enter a radio station into the AVR45's preset memory. After pressing the button the MEMORY indicator N will flash, and you then have five seconds to enter a present memory location using the Numeric Keys l. (See page 26 for more information.) NOTE: Although the word "Sleep" appears above this button, it refers to control of devices other than the AVR45. Use the Sleep button ` to control the AVR45's Sleep function. o Info Button: This button does not function with the AVR45, but it is available for use with other devices. p Light Button: Press this button to activate the remote's built-in backlight for better legibility of the buttons in a darkened room. q Tuner Mode: Press this button when the tuner is in use to select between automatic tuning and manual tuning. When the button is pressed so that the AUTO indicator O goes out, pressing the Tuning buttons t will move the frequency up or down in single-step increments. When the FM band is in use, pressing this button when a station's signal is weak will change to monaural reception, as indicated by the MONO indicator Q. (See page 26 for more information.) r Clear Button: This button does not function with the AVR45, but it is available for use with other devices. s Preset Up/Down: When the tuner is in use, these buttons scroll through the stations that have been programmed into the AVR45's memory. When many source devices, such as CD players, VCRs and cassette decks, are selected using the Device Control Selectors b, these buttons will normally function as chapter step or track advance. t Tuning Up/Down: When the tuner is in use, these buttons will tune up or down through the selected frequency band. If the Tuner Mode button q has been pressed so that the AUTO indicator O is illuminated, pressing these buttons will cause the tuner to seek the next station with acceptable signal strength for quality reception. When the AUTO indicator O is NOT illuminated, pressing these buttons will tune stations in single-step increments. (See page 26 for more information.) u Transport Controls: These controls do not control any functions of the AVR45, but they are used extensively when operating a wide variety of CD players, cassette decks and VCRs. (See page 28 for information on programming the remote to utilize these buttons.) v Delay/Prev Ch.: Press this button to begin the process for setting the delay times used by the AVR45 when processing surround sound. After pressing this button the delay times are entered by pressing the Set button i, and then using the ⁄/ ¤ buttons g to change the setting. Press the Set button again to complete the process. (See page 20 for more information.) w ›/Digital Button: This button is used to select the type of digital input used with any one of the input sources connected to the AVR45. After pressing this button, use the ⁄/ ¤ buttons g to make your selection between OPTICAL E or COAXIAL G digital. Press the Set button i to enter your choice. (See page 24 for more information.) x Speaker Configuration: Press this button to begin the process of configuring the AVR45's Bass Management System for use with the type of speakers used in your system. Once the button has been pressed, use the ⁄/ ¤ buttons g to select the channel you wish to set up. Press the Set button i, and then select another channel to configure. When all adjustments have been completed, press the Set button twice to exit the settings and return to normal operation. (See page 17 for more information.) y Surround Mode Selector: Press this button to begin the process of changing the surround mode. After the button has been pressed, use the ⁄/ ¤ buttons g to select the desired surround mode. (See page 24 for more information.) Note that this button is also used to tune channels when the TV is selected using the Device Control Selector b. When the AVR45 remote is being programmed for the codes of another device, this button is also used in the "Auto Search" process. (See page 28 for more information on programming the AVR45 remote.) z Volume: Press these buttons to raise or lower the system volume. ` Sleep Button: Press this button to place the unit in the Sleep mode. After the time shown in the display, the AVR45 will automatically go into the Standby mode. Each press of the button changes the time until turn-off in the following order: 90 80 70 60 50 40 min min min min min min 30 min 20 min 10 min 5 min 1 min OFF Note that this button is also used to change channels on your TV when the TV is selected using the Device Control Selector b. When the AVR45 remote is being programmed for the codes of another device, this button is also used in the "Auto Search" process. (See page 28 for more information on programming the AVR45 remote.)