Harman Kardon HTFS 2BQ Owners Manual - Page 3

Assembly - e stand speaker

Get Harman Kardon HTFS 2BQ PDF manuals and user guides View all Harman Kardon HTFS 2BQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

ASSEMBLY Assembly 1. If you will be placing the HTFS 2 stands on a hard surface, such as a wood or tile floor, attach four of the supplied self-adhesive rubber pads to the underside of the base in the recesses as indicated in the drawing. 6. Attach the mounting plate to the top of the column using two of the supplied screws. The mounting plate tab with the third screw hole should sit on the higher rim of the column. Attaching the Speaker to the Stand 1. Unscrew the bolt that attaches the black shelf stand to the bottom of the speaker. Store the stand in a safe place in case it is needed for a future installation. The bolt will be used to attach the speaker to the floor stand mounting plate. Place rubber pads or floor spikes here 2. If you will be using the HTFS 2 stands on a carpeted surface, screw four of the supplied floor spikes into the base using the threaded inserts in the recesses as shown in the drawing. 3. Following the instructions on pages 9 through 12 of the owner's manual provided with your HKTS system, thread the appropriate speaker cable through the hole in the center of the base, being careful to avoid the two screw holes. Then feed the cable through the length of the column from the bottom until it comes out the top. 4. Attach the column to the base using two of the supplied screws. 5. Thread the speaker cable through the hole in the center of the mounting plate, being careful to avoid the three screw holes. 15mm or 1/2" Remove Stand 2. Insert the speaker wires into the terminals on the bottom of the speaker, being careful to observe the correct polarity. 3. Place the speaker on top of the mounting plate with the remaining screw hole lined up with the threaded insert on the bottom of the speaker. 4. Insert the bolt that was used for the shelf stand up through the remaining screw hole and into the speaker. Repeat the assembly and speaker attachment processes for each floor stand in your system, and adjust the final speaker placement as indicated in the owner's manual supplied with the speakers. You are now ready to enjoy your home theater system! ASSEMBLY 3

  • 1
  • 2
  • 3
  • 4
ASSEMBLY
3
ASSEMBLY
Assembly
1. If you will be placing the HTFS 2 stands
on a hard surface, such as a wood or
tile floor, attach four of the supplied
self-adhesive rubber pads to the
underside of the base in the recesses
as indicated in the drawing.
Place rubber pads or floor spikes here
2. If you will be using the HTFS 2 stands
on a carpeted surface, screw four of the
supplied floor spikes into the base using
the threaded inserts in the recesses as
shown in the drawing.
3. Following the instructions on pages 9
through 12 of the owner’s manual
provided with your HKTS system, thread
the appropriate speaker cable through
the hole in the center of the base, being
careful to avoid the two screw holes.
Then feed the cable through the length
of the column from the bottom until it
comes out the top.
4. Attach the column to the base using two
of the supplied screws.
5. Thread the speaker cable through
the hole in the center of the mounting
plate, being careful to avoid the three
screw holes.
6. Attach the mounting plate to the top of
the column using two of the supplied
screws. The mounting plate tab with the
third screw hole should sit on the higher
rim of the column.
Attaching the Speaker
to the Stand
1. Unscrew the bolt that attaches the black
shelf stand to the bottom of the speaker.
Store the stand in a safe place in case it
is needed for a future installation. The bolt
will be used to attach the speaker to the
floor stand mounting plate.
2. Insert the speaker wires into the terminals
on the bottom of the speaker, being care-
ful to observe the correct polarity.
3. Place the speaker on top of the mounting
plate with the remaining screw hole lined
up with the threaded insert on the bottom
of the speaker.
4. Insert the bolt that was used for the shelf
stand up through the remaining screw
hole and into the speaker.
Repeat the assembly and speaker attach-
ment processes for each floor stand in your
system, and adjust the final speaker place-
ment as indicated in the owner’s manual
supplied with the speakers. You are now
ready to enjoy your home theater system!
Remove
Stand
15mm
or 1/2"