Hayward ColorLogic 4.0 Model: ALL MODELS Programming Guide - Page 1

ColorLogic 4.0 Lights Programming Start Here Press repeatedly until "Settings Menu" is displayed Settings Menu Press the or button until "Aux1 Settings" is displayed Aux1 Settings + to view/change Press to proceed How to Program a Light Show Press the or button until the desired light show is displayed Aux1 Program 7 Twilight Refer to the Program Table on page 1 of the manual to determine which show you would like to program. Select Show 1 or Shows 7-16. The name, number and a description of each show can be found on the Program Table. Custom Shows: Show 15 (Custom Fade) and Show 16 (Custom Chase) are unique light shows. Rather than using preset light colors, these shows use the 5 fixed colors from the Program Table (numbered 2-6). These 5 fixed colors can be programmed to display any color (see Program Fixed Light). Shows 15 and 16 will use these "new" fixed colors in their shows, giving the user complete control over all parameters. Note that Custom Shows 15 and 16 will display the 5 fixed colors in the following order: 2, 3, 4, 6, 5. Press the button to advance to the Speed programming screen Press the or button to set the desired speed Aux1 Speed X1 This is the speed at which the entire sequence of lights within the lights show, will run. Use the "+" and "-" buttons to increase or decrease this speed. The selectable range is 1/16 to x16 (default is x1). Press the button to advance to the Motion programming screen How to Program a Fixed Color Press the or button until the desired fixed color is displayed Aux1 Program 2 Deep Blue Sea 1 Refer to the Program Table on page 1 of the manual to determine which fixed color you would like to program. Select fixed color 2, 3, 4, 5 or 6. The name, number and a description of each fixed color can be found on the Program Table. You will have an opportunity to change this fixed color to a custom color, if desired. Press the button to advance to the Custom Color programming screen Press the or Press button to change to a custom color, then press or to keep the factory default fixed color 2 Custom Color 75 +/- to change color Select the desired fixed light and press "+" or "-" to change the color. The name will change to "Custom Color" and the number to the right will change to a new value. Refer to this number and the included color card to determine the desired color. NOTE: If any of the factory fixed colors are changed, Program 15 (Custom Fade) and Program 16 (Custom Chase) will use the new fixed color in their light shows. If factory default color is kept If changed to a custom color Press the or button to set the desired motion Aux1 Motion +0.2 The motion selection affects two aspects of a light show; the order in which the lights are illuminated and the fixed delay between each light in the sequence. Changing the delay between lights will give the perception of motion. Changing the order will give the perception of a change in direction. When set to OFF, there is no delay and all lights will illuminate at the same time. When motion is set to a positive value (+0.2 to +1.2), the order of illumination will start from the lowest LT number and advance to the highest. As the value is increased, the delay between each light is increased. If a negative motion value is selected (-1.2 to -0.2), the illumination sequence will be the opposite (highest LT to lowest). As the value is decreased, the delay between each light is increased. Press the button to advance to the Brightness programming screen Press the Press the to reset the custom color or Push to save the custom color 2 Custom Color 75 Press + to reset Before you can save the color, the option to reset back to the factory set color is displayed. If you press the "+" button, you can "undo" your changes and return back to the original default color. If you wish to keep the new color, push the ">" button to advance to the next screen. If button is pressed If button is pressed If button is pressed or button to set the desired brightness Aux1 Brightness 100% Push to reset color Are you sure? + to proceed Pushing the "+" button will reset to the original factory default color If button is pressed 2 Deep Blue Sea 1 Reset Confirmed Use the "+" or "-" buttons to adjust the brightness of the light show from 20% to 100% in 20% increments (default is 100%). Press to advance to the Brightness programming screen