Hayward Dyna-Skim SP1091LX - Page 3

Operating Instructions - installation

Get Hayward Dyna-Skim PDF manuals and user guides View all Hayward Dyna-Skim manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

Page 3 of 4 DYNA-SKIM SKIMMERS IS1091LX REV D RETURN FITTING INSTALLATION 1. The return fitting furnished with these skimmers is a SP1023. The hole required through the pool wall to install this fitting is 2.38±.03 inches. DO NOT CUT THE LINER. 2. Place one rubber gasket over the threads of the return fitting adapter and push the threaded end against the liner and through the return cutout in the wall. 3. Applying outward pressure to the return fitting cut and "X" in the center of the exposed liner from outside the pool. The return fitting will now be fully pressed against the liner and the wall on the inside of the pool. Using a razor knife, trim the excess liner material from around the fitting threads on the outside of the pool. 4. Place the second rubber gasket and then the cork gasket over the threads of the return fitting now exposed outside of the pool. Screw on the lock nut and tighten. 5. Screw on the adjustable directional ball fitting into the face of the return fitting from the outside of the pool. Position ball fitting opening away from skimmer opening. Do not over-tighten. Note: On-going leaks from the skimmer or wall fittings may cause pool wall damage that eventually may result in pool wall failure. RECOMMENDED WINTERIZING PROCEDURE Drain pool level approximately six inches (6") below skimmer opening. Remove Hydrostream Eyeball fitting and securely plug wall fitting (1 ½" threaded plugs are available from the dealer). Disconnect filter hoses from the skimmer and the wall fitting. Be sure that the skimmer is kept free of water accumulation. Warranty does not include damage caused by the formation of ice in the skimmer. OPERATING INSTRUCTIONS TO CLEAN SKIMMER BASKET TO-VACUUM WITH SKIM-VAC Remove top cover; or fold weir forward and squeeze tabs 1. Remove weir from front of skimmer. toward center to remove weir. Remove and clean basket. 2. Attach vacuum hose to vac head and handle, and fill Deluxe Skim-Vac Accessory vacuum hose with water (place over pool inlet). Place SKIM-VAC attaches to vac hose and is inserted in skimmer SKIM-VAC over skimmer basket. Going through the over basket, allowing you to conveniently vacuum through the skimmer opening in the pool wall, attach the vacuum hose skimmer basket. to the SKIM-VAC hose adapter. 3. Hold SKIM-VAC in place until any air hose is evacuated by pump. Once air is removed, the pump suction will hold the SKIM-VAC firmly in place. Note: Take care not to damage or scuff the SKIM-VAC's specially designed sealing surface.

  • 1
  • 2
  • 3
  • 4
Page 3 of 4
DYNA-SKIM SKIMMERS
IS1091LX
REV D
RETURN FITTING INSTALLATION
1.
The return fitting furnished with these skimmers is a SP1023.
The hole required through the pool wall to install this fitting is
2.38±.03 inches.
DO NOT CUT THE LINER
.
2.
Place one rubber gasket over the threads of the return fitting adapter and push the threaded end against the liner and through
the return cutout in the wall.
3.
Applying outward pressure to the return fitting cut and “X” in the center of the exposed liner from outside the pool.
The
return fitting will now be fully pressed against the liner and the wall on the inside of the pool.
Using a razor knife, trim the
excess liner material from around the fitting threads on the outside of the pool.
4.
Place the second rubber gasket and then the cork gasket over the threads of the return fitting now exposed outside of the pool.
Screw on the lock nut and tighten.
5.
Screw on the adjustable directional ball fitting into the face of the return fitting from the outside of the pool.
Position ball
fitting opening away from skimmer opening.
Do not over-tighten.
Note:
On-going leaks from the skimmer or wall fittings may cause pool wall
damage that eventually may result in pool wall failure.
RECOMMENDED WINTERIZING PROCEDURE
Drain pool level approximately six inches (6”) below skimmer opening.
Remove
Hydrostream Eyeball fitting and securely plug wall fitting (1 ½” threaded plugs are
available from the dealer).
Disconnect filter hoses from the skimmer and the wall
fitting.
Be sure that the skimmer is kept free of water accumulation.
Warranty does
not include damage caused by the formation of ice in the skimmer.
TO CLEAN SKIMMER BASKET
Remove top cover; or fold weir forward and squeeze tabs
toward center to remove weir.
Remove and clean basket.
Deluxe Skim-Vac Accessory
SKIM-VAC attaches to vac hose and is inserted in skimmer
over basket, allowing you to conveniently vacuum through the
skimmer basket.
TO-VACUUM WITH SKIM-VAC
1.
Remove weir from front of skimmer.
2.
Attach vacuum hose to vac head and handle, and fill
vacuum hose with water (place over pool inlet).
Place
SKIM-VAC over skimmer basket.
Going through the
skimmer opening in the pool wall, attach the vacuum hose
to the SKIM-VAC hose adapter.
3.
Hold SKIM-VAC in place until any air hose is evacuated
by pump.
Once air is removed, the pump suction will
hold the SKIM-VAC firmly in place.
Note:
Take care not to damage or scuff the SKIM-VAC’s
specially designed sealing surface.
OPERATING INSTRUCTIONS