Hayward W3AQR15 AquaRite-Electronic-Chlorine-Generator-Owners-Manual-092540Rev - Page 2

Important Safety Instructions

Get Hayward W3AQR15 PDF manuals and user guides View all Hayward W3AQR15 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

IMPORTANT SAFETY INSTRUCTIONS When using this electrical equipment, basic safety precautions should always be followed, including the following: • READ AND FOLLOW ALL INSTRUCTIONS • Disconnect all AC power during installation. • WARNING - To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. • A green colored terminal marked "Earth Ground" is located inside the wiring compartment. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying the equipment. • WARNING - Risk of Electric Shock. Connect only to a grounding type receptacle protected by a ground-fault circuit-interrupter (GFCI). Contact a qualified electrician if you cannot verify that the receptacle is protected by a GFCI. • Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment. • WARNING - To reduce the risk of electric shock, replace damaged cord immediately. • WARNING - To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet. • Two bonding lugs are provided on the exterior enclosure, one to be used for US installations and both for Canadian. To reduce the risk of electric shock, connect the local common bonding grid in the area of the swimming pool, spa, or hot tub to these terminals with an insulated or bare copper conductor not smaller than 8 AWG US / 6 AWG Canada. • All field installed metal components such as rails, ladders, drains, or other similar hardware within 3 meters of the pool, spa or hot tub shall be bonded to the equipment grounding bus with copper conductors not smaller than 8 AWG US / 6 AWG Canada. • Hayward salt systems are designed, tested and sold as systems and are certified by several agencies around the globe --- with each component of the systems meeting all required certifications and attendant legal requirements. The use of an untested, uncertified generic cells (or generic circuit boards) with Genuine Hayward salt chlorination products could lead to premature product failure. • Pursuant to the terms and conditions of any applicable Warranty, the use of a non-genuine Hayward replacement salt chlorination cell on any Hayward automation or chlorination product will void any Warranty. SAVE THESE INSTRUCTIONS 1 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be followed, includ-
ing the following:
•
READ AND FOLLOW ALL INSTRUCTIONS
•
Disconnect all AC power during installation.
•
WARNING
- To reduce the risk of injury, do not permit children to use this product unless they
are closely supervised at all times.
•
A green colored terminal marked "Earth Ground" is located inside the wiring compartment.
To reduce the risk of electric shock, this terminal must be connected to the grounding means
provided in the electric supply service panel with a continuous copper wire equivalent in size
to the circuit conductors supplying the equipment.
•
WARNING
- Risk of Electric Shock.
Connect only to a grounding type receptacle protected
by a ground-fault circuit-interrupter (GFCI).
Contact a qualified electrician if you cannot verify
that the receptacle is protected by a GFCI.
•
Do not bury cord.
Locate cord to minimize abuse from lawn mowers, hedge trimmers, and
other equipment.
•
WARNING
- To reduce the risk of electric shock, replace damaged cord immediately.
•
WARNING
- To reduce the risk of electric shock, do not use extension cord to connect unit to
electric supply; provide a properly located outlet.
•
Two bonding lugs are provided on the exterior enclosure, one to be used for US installations
and both for Canadian. To reduce the risk of electric shock, connect the local common bond-
ing grid in the area of the swimming pool, spa, or hot tub to these terminals with an insulated
or bare copper conductor not smaller than 8 AWG US / 6 AWG Canada.
•
All field installed metal components such as rails, ladders, drains, or other similar hardware
within 3 meters of the pool, spa or hot tub shall be bonded to the equipment grounding bus
with copper conductors not smaller than 8 AWG US / 6 AWG Canada.
•
Hayward salt systems are designed, tested and sold as systems and are certified by several
agencies around the globe --- with each component of the systems meeting all required
certifications and attendant legal requirements. The use of an untested, uncertified generic
cells (or generic circuit boards) with Genuine Hayward salt chlorination products could lead to
premature product failure.
•
Pursuant to the terms and conditions of any applicable Warranty, the use of a non-genuine
Hayward replacement salt chlorination cell on any Hayward automation or chlorination product
will void any Warranty.
SAVE THESE INSTRUCTIONS
1
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS