Hayward W3SP2303VSP 1.65 THP VS Pump Family - Owners Manual - Page 18

< &gt

Get Hayward W3SP2303VSP PDF manuals and user guides View all Hayward W3SP2303VSP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Screen 6. Set Day and Time Thursday 1:27p Buttons Used + < > Comments Adjust day/time setting. Move to next selection, then move to next menu item. 7. Speed Selection rpm + - Select pump speed display: rpm (revolutions per minute) or % of full speed. < > Move to next menu item. 8. Max allowed speed 3450 (600-3450rpm) + - Set maximum running speed of pump. < > Move to next menu item. 9. Min allowed speed 600 (600-3450rpm) + - Set minimum running speed of pump. < > Move to next menu item. 10. Prime Duration 8:00 minutes + - Select pump prime duration. < > Move to next menu item. NOTE: User may set the pump to prime at the maximum allowed speed for 0-15 minutes in 30 second increments. Remote Control Mode 11. Stand Alone + - Select Stand Alone or Relay Control. < > Move to next menu item. NOTE: See page 12 for more detail. 12. Low Temp Operation Disabled + - Enable or Disable Low Temp Operation. < > Move to next menu item. 13. Low Temp Setting 4°C (39.2°F) + - Set temperature to activate Low Temp Operation. < > Move to next menu item. NOTE: When the pump is stopped and the ambient temperature drops below the operation temperature set point, the pump will prime and then run at the Max allowed speed setting for 8 hours. Low temperature operation is not active when the pump is being remotely controlled. Low temperature operation is NOT intended to protect the pump, system plumbing, or pool from freezing. If Low Temp Operation is disabled, the temperature setting screen is not shown. 14. Password Protection Disabled + - Use to enable or disable password protection. < > Move to next menu item. 15. Password Timeout 0:15 + - Use to set password timeout. < > Move to next menu item. NOTE: This sets the amount of time from the last button activation after the system has been unlocked to the point where the system becomes locked again. 16. System Password + change or > skip + - Use to set password timeout. < > Move to next menu item. 17 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
17
6.
7.
8.
9.
10.
NOTE: User may set the pump to prime at the maximum allowed speed for 0-15 minutes in 30 second increments.
11.
NOTE: See page 12 for more detail.
12.
13.
NOTE: When the pump is stopped and the ambient temperature drops below the operation temperature set point, the pump will prime and then run at the Max
allowed speed setting for 8 hours. Low temperature operation is not active when the pump is being remotely controlled.
Low temperature operation is NOT
intended to protect the pump, system plumbing, or pool from freezing.
If Low Temp Operation is disabled, the temperature setting screen is not shown.
14.
15.
NOTE: This sets the amount of time from the last button activation after the system has been unlocked to the point where the system becomes locked again.
16.
System Password
+
change or
>
skip
Use to set password timeout.
Move to next menu item.
+ -
< >
Password Protection
Disabled
Password Timeout
0:15
Use to enable or disable password protection.
Move to next menu item.
Use to set password timeout.
Move to next menu item.
+ -
< >
+ -
< >
Low Temp Operation
Disabled
Low Temp Setting
4
±
C
(39.2
±
F)
Enable or Disable Low Temp Operation.
Move to next menu item.
Set temperature to activate Low Temp Operation.
Move to next menu item.
+ -
< >
+ -
< >
Remote Control Mode
Stand Alone
Select Stand Alone or Relay Control.
Move to next menu item.
+ -
< >
Adjust day/time setting.
Move to next selection, then move to next menu item.
Select pump speed display: rpm (revolutions per minute) or % of full speed.
Move to next menu item.
Set maximum running speed of pump.
Move to next menu item.
Screen
Buttons Used
Comments
Set Day and Time
Thursday
1:27p
Speed Selection
rpm
Max allowed speed
3450
(600-3450rpm)
Min allowed speed
600
(600-3450rpm)
Prime Duration
8:00
minutes
Set minimum running speed of pump.
Move to next menu item.
Select pump prime duration.
Move to next menu item.
+ -
< >
+ -
< >
+ -
< >
+ -
< >
+ -
< >