HealthRider T90 Treadmill English Manual - Page 8

Tighten all four Handrail Bolts 111.

Get HealthRider T90 Treadmill PDF manuals and user guides View all HealthRider T90 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

4. Pull the Upright Wire Harness (101) and the TV Cable (104) up through the Right Handrail Spacer (107) (refer to drawing A to distinguish the Right Handrail Spacer from the Left Handrail Spacer [106]). Place the Right Handrail Spacer on the right Upright (110). Connect the Upright Wire Harness (101) and the TV Cable (104) to the two wires extending from the Console Base (76). Insert the connectors, the Upright Wire Harness, and the TV Cable into the hole in the Console Base (refer to inset drawing B). Set the Handrail (89) on the Right Handrail Spacer (107), being careful not to pinch the Upright Wire Harness (101) and the TV Cable (104). 5. Insert two Handrail Bolts (111) with Handrail Washers (112) into the right Upright (110) and the Right Handrail Spacer (107). Lift the right Handrail (89) slightly and align the Bolts with the holes in the Handrail. Loosely thread the Bolts into the Handrail. Do not tighten the Bolts yet. Refer to step 3. Remove the Handrail Bolt (111) from the left Upright (110) and the left Handrail (89). Place the Left Handrail Spacer (106, not shown) on the left Upright (110, not shown). Attach the left Handrail (89) as described above. Tighten all four Handrail Bolts (111). 4 76 A 106 89 107 110 107 101 B 101 104 104 76 5 89 107 110 112 111 6. Attach the Latch Assembly (109) to the left Upright (110) with two Latch Screws (86). 6 86 110 7. Note the location of the 75 ohm antenna terminal on the treadmill. For the television to operate properly, an antenna, a CATV cable, or a VCR must be connected to the 75 ohm antenna terminal. 7 If you are using an antenna, it must be properly connected and adjusted for optimal reception. Refer to ANTENNA CONNECTIONS on page 22 to properly connect an antenna. If you are using a CATV cable, refer to CATV CABLE CONNECTION on page 22 to properly connect the cable. If you are using a VCR, refer to HOW TO CONNECT A VCR on page 24 to properly connect the VCR. The VCR must be turned on, a videocassette must be properly inserted, and the VCR must be playing. Refer to your VCR user's manual for operating instructions. 109 75 Ohm Antenna Terminal 8 . Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 27). To protect the floor or carpet from damage, place a mat under the treadmill. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
8 .
Make sure that all parts are tightened before you use the treadmill.
Keep the included allen wrench in a
secure place. The allen wrench is used to adjust the walking belt (see page 27). To protect the floor or carpet
from damage, place a mat under the treadmill.
5.
Insert two Handrail Bolts (111) with Handrail Washers
(112) into the right Upright (110) and the Right Handrail
Spacer (107). Lift the right Handrail (89) slightly and align
the Bolts with the holes in the Handrail. Loosely thread
the Bolts into the Handrail.
Do not tighten the Bolts yet.
Refer to step 3. Remove the Handrail Bolt (111) from the
left Upright (110) and the left Handrail (89).
Place the Left Handrail Spacer (106, not shown) on the
left Upright (110, not shown). Attach the left Handrail (89)
as described above.
Tighten all four Handrail Bolts (111).
111
112
110
89
4.
Pull the Upright Wire Harness (101) and the TV Cable
(104) up through the Right Handrail Spacer (107) (refer to
drawing A to distinguish the Right Handrail Spacer from
the Left Handrail Spacer [106]). Place the Right Handrail
Spacer on the right Upright (110).
Connect the Upright Wire Harness (101) and the TV
Cable (104) to the two wires extending from the Console
Base (76). Insert the connectors, the Upright Wire
Harness, and the TV Cable into the hole in the Console
Base (refer to inset drawing B).
Set the Handrail (89) on the Right Handrail Spacer (107),
being careful not to pinch the Upright Wire Harness (101)
and the TV Cable (104).
4
101
110
89
76
107
104
107
106
76
101
104
A
B
107
6.
Attach the Latch Assembly (109) to the left Upright (110)
with two Latch Screws (86).
109
110
86
6
7.
Note the location of the 75 ohm antenna terminal on
the treadmill. For the television to operate properly, an
antenna, a CATV cable, or a VCR must be connected
to the 75 ohm antenna terminal.
If you are using an antenna,
it must be properly con-
nected and adjusted for optimal reception. Refer to AN-
TENNA CONNECTIONS on page 22 to properly connect
an antenna.
If you are using a CATV cable,
refer to
CATV CABLE CONNECTION on page 22 to properly con-
nect the cable.
If you are using a VCR,
refer to HOW TO
CONNECT A VCR on page 24 to properly connect the
VCR.
The VCR must be turned on, a videocassette
must be properly inserted, and the VCR must be play-
ing. Refer to your VCR user’s manual for operating in-
structions.
7
75 Ohm Antenna
Terminal
8
5