HP 220mx HP SureStore 300mx/600mx/700mx Optical Jukebox User's Guide - Page 71

Press, You may have to wait for the, application to replace the disk into the slot, before

Get HP 220mx PDF manuals and user guides View all HP 220mx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Operating the Jukebox Operating the Jukebox Troubleshooting Problem What to do Disk eject attempted but RESERVED displays. The jukebox application software reserved the element for its use or a security configuration was set to prevent disk ejection. • If appropriate, change this setting See "Setting an Operating Configuration" in this chapter. The current administration password is required. Disk eject attempted but This is not an error. There are no disks in the empty and then EJECT * jukebox. displays. Disk eject attempted but TRANSPORT FULL displays. The disk transport mechanism already contains a disk. • Refer to your host and application documentation for recovery procedures. If no procedures are available, call your service representative. Disk eject attempted but SOURCE NOW EMPTY displays. The application software moved the disk from the slot you chose before your eject command executed. • Press CANCEL. You may have to wait for the application to replace the disk into the slot before attempting another eject. Disk eject attempted but MAILSLOT FULL displays. A disk is in the mailslot. • Remove the disk from the mailslot. Select EJECT *, select the slot you want the disk ejected from again, and eject the disk. You want to stop a test that is running. Press CANCEL. The current test loop continues until finished, then the test stops. *Ensure that the SCSI bus is inactive before removing power to the jukebox. Removing power to a device on an active SCSI bus can cause data loss and/or problems with the SCSI interface. Chapter 3 3-37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Chapter 3
3-37
Operating the Jukebox
Troubleshooting
Operating the
Jukebox
Disk eject attempted but
RESERVED
displays.
The jukebox application software reserved the
element for its use or a security configuration was
set to prevent disk ejection.
•
If appropriate, change this setting See
“
Setting
an Operating Configuration
”
in this chapter. The
current administration password is required.
Disk eject attempted but
empty and then
EJECT *
displays.
This is not an error. There are no disks in the
jukebox.
Disk eject attempted but
TRANSPORT FULL
displays.
The disk transport mechanism already contains a
disk.
•
Refer to your host and application
documentation for recovery procedures. If no
procedures are available, call your service
representative.
Disk eject attempted but
SOURCE NOW EMPTY
displays.
The application software moved the disk from the
slot you chose before your eject command executed.
•
Press
CANCEL
.
You may have to wait for the
application to replace the disk into the slot
before attempting another eject.
Disk eject attempted but
MAILSLOT FULL
displays.
A disk is in the mailslot.
•
Remove the disk from the mailslot.
Select
EJECT *
, select the slot you want the
disk ejected from again, and eject the disk.
You want to stop a test
that is running.
Press
CANCEL
. The current test loop continues until
finished, then the test stops.
*Ensure that the SCSI bus is inactive before removing power to the jukebox.
Removing power to a device on an active SCSI bus can cause data loss and/or
problems with the SCSI interface.
Problem
What to do