Home » HP Manuals » Hubs & Switches » HP 279720-B21 » Manual Viewer

HP 279720-B21 ProLiant BL p-Class GbE Interconnect Switch Command Line Interfa - Page 94

Displaying Ingress Filtering Information, Configuring Port Mirroring - target

UPC - 613326400081

Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Configuring the GbE Interconnect Switch using the Command Line Interface Displaying Ingress Filtering Information Use the following command to display the ingress filtering information on a per port basis: Command ingress-filter show [port ] Description Displays ingress filtering information for all ports To display ingress information for a specified port or ports, type port and the port number or numbers. This example shows the ingress filtering information for a series of ports. Configuring Port Mirroring The GbE Interconnect Switch allows you to copy frames transmitted and received on a port (source) and redirect the copies to another port (target). You can attach a monitoring device to the mirrored (target) port, such as a sniffer or an RMON probe, to view details about the packets passing through the source port. This setting is useful for network monitoring and troubleshooting purposes. The following configuration rules apply to any port mirroring configuration: • A target mirror port cannot be configured as a trunk member. • VLAN configuration settings for any ports configured for mirroring cannot be changed. • The source and target ports should be members of the same VAN. The direction of traffic on the source port can be one of the following: • Ingress traffic (received packets) on the source port • Egress traffic (transmitted packets) on the source port • Ingress and egress traffic on the source port IMPORTANT: You cannot mirror a fast port onto a slower port. For example, if you try to mirror the traffic from a 1000-Mb/s port onto a 100-Mb/s port, you can cause throughput problems. The port from which you are copying frames must support an equal or lower speed than the port to which you are sending the copies. HP ProLiant BL p-Class GbE Interconnect Switch Command Line Interface Reference Guide 2-73 HP CONFIDENTIAL Codename: DeLorean Part Number: 322604-001 Last Saved On: 2/3/03 11:35 AM

Section	Page
HP ProLiant BL p-Class GbE Interconnect Switch Command Line Interface Reference Guide	1
Notice	2
Contents	3
About This Guide	8
Technician Notes	8
Where to Go for Additional Help	9
Telephone Numbers	9
Chapter 1: Overview	10
Introduction	10
Additional References	10
Before You Begin	10
Connecting to the GbE Interconnect Switches	11
Logging On to the GbE Interconnect Switch	11
Moving Between the Console Management Interfaces	12
Setting the Default Interface	13
Displaying the Default Interface	13
Using the CLI	13
Understanding Command Syntax Symbols	13
Understanding Common Parameter Definitions	15
Using Command Line Editing Keys	16
Executing a Command	17
Command Help	17
Question Mark (?)	18
Using Command Completion	18
Displaying Command History	19
Customizing the Command Prompt	20
Clearing the CLI Screen	20
Paging of Data Output	21
Configuring the GbE Interconnect Switch	21
Chapter 2: Configuring the GbE Interconnect Switch using the Command Line Interface	22
Overview	22
Saving Changes	22
Managing User Accounts	23
Adding a User Account	24
Deleting a User Account	25
Displaying User Account Information	25
Updating User Account Information	25
Configuring Remote Management IP Interface Settings	26
Setting the Remote Management IP Interface Settings	27
Displaying Remote Management Interface Settings	29
Deleting the Secure IP Addresses	29
Configuring Basic GbE Interconnect Switch Information	30
Setting System Name, Location, and Contact Information	30
Displaying GbE Interconnect Switch Information	30
Configuring Auto-Logout Timer	34
Setting the Auto-Logout Time	34
Displaying Auto-Logout Timer Settings	35
Configuring MAC Address Aging Timer	35
Setting the MAC Address Age	36
Displaying MAC Address Aging Timer Information	36
Clearing MAC Address Monitoring Table	38
Configuring IGMP Snooping	39
Enabling IGMP Snooping	40
Disabling IGMP Snooping	41
Setting IGMP Filter Mode for Processing Multicast Packets	41
Adding IGMP Snooping Settings for a VLAN	42
Modifying IGMP Settings for a VLAN	43
Deleting IGMP Snooping Settings for a VLAN	44
Displaying IGMP Snooping Settings	44
Configuring Class of Service, Default Port Priority, and Traffic Class	46
Setting Class of Service, Default Port Priority, and Traffic Class	46
Displaying CoS Queue Information	48
Configuring Port Trunking	49
Considerations when Creating a Port Trunking Group	50
Creating a Port Trunk Group	51
Adding a Port to an Existing Trunk	51
Deleting a Trunk Group or a Port from a Trunk Group	52
Enabling a Trunk Group	52
Disabling a Trunk Group	52
Clearing Trunk Utilization Counters	52
Configuring the Trunk Load Sharing Algorithm Options	53
Displaying Trunk Load-Sharing Algorithm	53
Configuring GVRP	54
Enabling GVRP Globally or on a Per Port Basis	55
Disabling GVRP Globally or on a Per Port Basis	55
Displaying GVRP Settings	56
Configuring Telnet and Web Access Settings	56
Enabling Telnet Access	56
Disabling Telnet Access	57
Displaying Telnet Access Settings	57
Enabling Web Access	57
Disabling Web Access	57
Displaying Web Access Settings	58
Configuring Backpressure Flow Control	58
Enabling Backpressure Flow Control	58
Disabling Backpressure Flow Control	58
Displaying Backpressure Flow Control Settings	59
Configuring GbE Interconnect Switch Date and Time	59
Setting Date and Time Parameters Manually	60
Displaying Time Parameters	62
Enabling SNTP	62
Setting SNTP Parameters	63
Displaying SNTP Parameters	63
Disabling SNTP	64
Configuring Port Settings	64
Speed/Duplex Settings	64
Port Security Settings	65
Setting Port Parameters	66
Enabling Ports on a Per Port Basis	67
Disabling Ports or Port Security on a Per Port Basis	67
Clearing Current Port Statistics	67
Displaying Current Port Settings and Port Names	68
Configuring Bandwidth	70
Adding and Configuring Restart Port Bandwidth Units	70
Deleting Ports from the Ingress and Egress Bandwidth Tables	71
Modifying Ingress and Egress Bandwidth Parameters	71
Displaying Current and Restart Port Bandwidth Settings	72
Configuring Spanning Tree Protocol	72
Enabling STP	74
Disabling STP	75
Setting Global and Per Port STP Parameters	75
Displaying STP Bridging and Per Port Settings	78
Configuring Static (Destination Address) Filtering Table	79
Adding Unicast Filter Actions	80
Modifying Unicast Filter Actions	81
Deleting the Unicast Filter Actions	82
Displaying Unicast Filter Actions	82
Adding Multicast Filter Actions	83
Modifying Multicast Filter Actions	83
Deleting Multicast Filter Actions	84
Displaying Multicast Filter Settings for a VLAN	84
Configuring VLANs	85
Default VLAN	86
Creating an 802.1Q Static VLAN	87
Adding a Port to an Existing VLAN	88
Deleting a VLAN or a Port from an Existing VLAN	89
Modifying the Per Port VLAN Settings or VLAN Name	90
Setting the PVID for a Port	91
Displaying VLAN Settings and Status	92
Enabling Ingress Filtering on a Per Port Basis	93
Disabling Ingress Filtering on a Per Port Basis	93
Displaying Ingress Filtering Information	94
Configuring Port Mirroring	94
Enabling Mirroring on a Port	95
Disabling Mirroring on a Port	95
Displaying Port Mirroring Status	96
Configuring Thresholds for Broadcast, Multicast, DA-Unknown Storm Prevention or Monitoring	96
Enabling Broadcast, Multicast, or DA-Unknown Packet Storm Monitoring	97
Disabling Monitoring Broadcast, Multicast, DA-Unknown Storm Monitoring	97
Configuring Storm Threshold in Packets Per Second	97
Displaying Broadcast, Multicast, DA-Unknown Storm Current Settings	97
Configuring Priority MAC Address	98
Adding Priority Level for a MAC Address	98
Deleting Priority Level for a MAC Address	99
Modifying Priority Level for a MAC Address	99
Displaying Current Priority Level for a MAC Address	100
Configuring GbE Interconnect Switch Serial Port	100
Configuring the GbE Interconnect Switch Serial Port Settings	101
Displaying Current GbE Interconnect Switch Serial Interface Settings	102
Configuring the History Log	102
Displaying the History Log	103
Clearing the History Log	104
Configuring SNMP/RMON Manager	104
Adding SNMP Management Interface Community Strings	105
Deleting SNMP Management Interface Community Strings	107
Displaying Current SNMP Management Interface Settings	107
Using System Utilities	108
Setting TFTP	108
Initiating a TFTP Download for Firmware or Configuration File	109
Initiating a TFTP Upload for Log File or Configuration File	110
Displaying TFTP Parameters	111
Performing a Ping Test	112
Rebooting the GbE Interconnect Switch	112
Logging Out	112
Appendix A: Commands	113
Introduction	113
Using the Command Line Interface	113
Saving Changes	113
Managing User Accounts	114
Configuring Remote Management IP Interface Settings	114
Configuring Basic GbE Interconnect Switch Information	115
Configuring Auto-Logout Timer	115
Configuring MAC-Address Aging Timer	116
Configuring IGMP Snooping	117
Configuring Class of Service, Default Port Priority, and Traffic Class	118
Configuring Port Trunking	119
Configuring GVRP	120
Configuring Telnet and Web Access Settings	120
Configuring Backpressure Flow Control	120
Configuring GbE Interconnect Switch Date and Time	121
Enabling Simple Network Time Protocol (SNTP)	122
Configuring Port Settings	123
Configuring Bandwidth	124
Configuring Spanning Tree Protocol	125
Configuring Static (Destination Address) Filtering Table	126
Configuring VLANs	127
Configuring Port Mirroring	128
Configuring Thresholds for Broadcast, Multicast, Unknown Storm Prevention or Monitoring	129
Configuring Priority MAC Address	129
Configuring GbE Interconnect Switch Serial Port	130
Configuring the History Log	130
Configuring SNMP Manager	131
Using System Utilities	132
Rebooting the GbE Interconnect Switch	132
Logging Out	132

Match case Limit results 1 per page

Configuring the GbE Interconnect Switch using the Command Line Interface

Displaying Ingress Filtering Information

Use the following command to display the ingress filtering information on a per port basis:

Command

Description

ingress-filter show

[port

]

Displays ingress filtering information for all ports

To display ingress information for a specified

port or ports, type

port

and the port number or

numbers.

This example shows the ingress filtering information for a series of ports.

Configuring Port Mirroring

The GbE Interconnect Switch allows you to copy frames transmitted and received on a port

(source) and redirect the copies to another port (target). You can attach a monitoring device

to the mirrored (target) port, such as a sniffer or an RMON probe, to view details about the

packets passing through the source port. This setting is useful for network monitoring and

troubleshooting purposes.

The following configuration rules apply to any port mirroring configuration:

•

A target mirror port cannot be configured as a trunk member.

VLAN configuration settings for any ports configured for mirroring cannot be changed.

The source and target ports should be members of the same VAN.

The direction of traffic on the source port can be one of the following:

Ingress traffic (received packets) on the source port

Egress traffic (transmitted packets) on the source port

Ingress and egress traffic on the source port

IMPORTANT:

You cannot mirror a fast port onto a slower port. For example, if you try to mirror the

traffic from a 1000-Mb/s port onto a 100-Mb/s port, you can cause throughput problems. The port from

which you are copying frames must support an equal or lower speed than the port to which you are

sending the copies.

HP ProLiant BL p-Class GbE Interconnect Switch Command Line Interface Reference Guide

2-73

HP CONFIDENTIAL

Codename: DeLorean Part Number: 322604-001 Last Saved On: 2/3/03 11:35 AM