HP AJ750A HP StorageWorks MSA2000 3.5-inch LFF Drive Enclosure Firmware releas - Page 9

Installation instructions using FTP - specification

Get HP AJ750A - StorageWorks Modular Smart Array 2000 Dual I/O Storage Enclosure PDF manuals and user guides
UPC - 883585832576
View all HP AJ750A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Installation instructions using FTP WARNING! Do not cycle power or restart devices during a firmware update. If the update is interrupted or there is a power failure, the module could become inoperative. If this occurs, contact technical support. The module may need to be returned to the factory for reprogramming. 1. Place the downloaded firmware package in a temporary directory. 2. If using a Smart Component, extract the contents of the Smart Component. In Windows - Click Extract on the first screen of the Smart Component. In Linux - Enter ./CPxxxxxx.scexe --unpack= to extract the contents of the Smart Component to the folder. For example,./CP001123.scexe -unpack=extract_here 3. Locate the firmware file in the extracted folder. The firmware filename is in the following format: mercurysw-O300B28-01.bin 4. Do one of the following: • To update all modules, proceed to step 5. • To update specific modules, do the following to determine the address of each module to update: In the CLI, display the addresses by entering the show enclosures command. The needed data is displayed in the columns labeled EMP A CH:ID Rev and EMP B CH:ID Rev. 5. In the SMU, prepare to use FTP: a. Determine the network-port IP addresses of the system controllers. b. Verify that the system FTP service is enabled. c. Verify that the user you will log in as has permission to use the FTP interface and has management access rights. 6. In single-domain environments, I/O to vdisks before starting the firmware update. 7. Open a command prompt (Windows) or a terminal window (UNIX), and navigate to the directory containing the firmware file to load. a. Enter ftp . (For example: ftp 10.1.0.9) b. Log in as an FTP user (user = ftp, password = flash). c. Enter one of the following commands: • To update all detected modules, enter: put encl flash. For example: put O300B28.bin encl flash • To update a specific module, enter: put encl:: flash. For example: put O300B28.bin encl:0:15 flash 8. If needed, repeat these steps to load the firmware on additional modules. 9. Quit the FTP session. 10. In the SMU display, verify that the proper firmware version appears for each module. HP StorageWorks MSA2000 3.5-inch LFF Drive Enclosure Firmware Release Notes 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
Installation instructions using FTP
WARNING!
Do not cycle power or restart devices during a firmware update. If the update is interrupted or there
is a power failure, the module could become inoperative. If this occurs, contact technical support. The
module may need to be returned to the factory for reprogramming.
1.
Place the downloaded firmware package in a temporary directory.
2.
If using a Smart Component,
extract the contents of the Smart Component.
In Windows
—
Click
Extract
on the first screen of the Smart Component.
In Linux
—
Enter
./CPxxxxxx.scexe --unpack=<folder name>
to extract the contents of
the Smart Component to the
<folder name>
folder. For example,
./CP001123.scexe
–
unpack=extract_here
3.
Locate the firmware file in the extracted folder. The firmware filename is in the following format:
mercurysw-O300B28-01.bin
4.
Do one of the following:
•
To update all modules, proceed to step 5.
•
To update specific modules, do the following to determine the address of each module to
update:
In the CLI, display the addresses by entering the
show enclosures
command. The needed
data is displayed in the columns labeled
EMP A CH:ID Rev
and
EMP B CH:ID Rev
.
5.
In the SMU, prepare to use FTP:
a.
Determine the network-port IP addresses of the system controllers.
b.
Verify that the system FTP service is enabled.
c.
Verify that the user you will log in as has permission to use the FTP interface and has
management access rights.
6.
In single-domain environments, I/O to vdisks before starting the firmware update.
7.
Open a command prompt (Windows) or a terminal window (UNIX), and navigate to the directory
containing the firmware file to load.
a.
Enter
ftp <controller-network-address>
. (For example:
ftp 10.1.0.9
)
b.
Log in as an FTP user (user =
ftp
, password =
flash
).
c.
Enter one of the following commands:
•
To update all detected modules, enter:
put <firmware-file> encl flash
. For
example:
put O300B28.bin encl flash
•
To update a specific module, enter:
put <firmware-file> encl:<channel-
ID>:<EMP-number> flash
. For example:
put O300B28.bin encl:0:15 flash
8.
If needed, repeat these steps to load the firmware on additional modules.
9.
Quit the FTP session.
10.
In the SMU display, verify that the proper firmware version appears for each module.
HP StorageWorks MSA2000 3.5-inch LFF Drive Enclosure Firmware Release Notes
9