HP BladeSystem bc2200 Service Reference Guide: HP BladeSystem PC Blade Enclosu - Page 27

Enclosure Status Assembly, CAUTION

Get HP BladeSystem bc2200 - Blade PC PDF manuals and user guides View all HP BladeSystem bc2200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

10. Lift the Integrated Administrator module off the anchor pins, and then remove the Integrated Administrator module from the interconnect tray (4). Figure 3-14 Removing the Integrated Administrator module from the interconnect tray Reverse the previous steps to replace the Integrated Administrator module. Enclosure Status Assembly To remove the enclosure status assembly: 1. Power down each HP Blade PC (Powering Down a Blade PC on page 12). 2. Power down the enclosure (Powering Down the Enclosure on page 10). 3. Disconnect all cables and power cords from the AC power source. 4. Disconnect all cables and power cords from the enclosure rear panel. 5. Remove all HP Blade PCs and HP Blade PC blank bezels (Removing a Blade PC on page 13 and Removing an HP Blade PC Blank Bezel on page 14). CAUTION: Integrated Administrator security settings are assigned to HP PC Blade Enclosure bays, not to HP Blade PCs. If HP Blade PCs change locations within the enclosure, Integrated Administrator settings must also be adjusted to ensure accurate security. Refer to the HP Integrated Administrator User Guide for more information about security settings. 6. Remove both hot-plug power supplies (Hot-Plug Power Supplies on page 8). 7. Remove the interconnect tray from the enclosure (Removing the Interconnect Tray on page 15). 8. Remove the enclosure from the rack (Removing the HP PC Blade Enclosure from the Rack on page 16). Non-Hot-Plug Procedures 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
10.
Lift the Integrated Administrator module off the anchor pins, and then remove the Integrated
Administrator module from the interconnect tray
(4)
.
Figure 3-14
Removing the Integrated Administrator module from the interconnect tray
Reverse the previous steps to replace the Integrated Administrator module.
Enclosure Status Assembly
To remove the enclosure status assembly:
1.
Power down each HP Blade PC (
Powering Down a Blade PC
on page
12
).
2.
Power down the enclosure (
Powering Down the Enclosure
on page
10
).
3.
Disconnect all cables and power cords from the AC power source.
4.
Disconnect all cables and power cords from the enclosure rear panel.
5.
Remove all HP Blade PCs and HP Blade PC blank bezels (
Removing a Blade PC
on page
13
and
Removing an HP Blade PC Blank Bezel
on page
14
).
CAUTION:
Integrated Administrator security settings are assigned to HP PC Blade Enclosure
bays, not to HP Blade PCs. If HP Blade PCs change locations within the enclosure, Integrated
Administrator settings must also be adjusted to ensure accurate security. Refer to the
HP
Integrated Administrator User Guide
for more information about security settings.
6.
Remove both hot-plug power supplies (
Hot-Plug Power Supplies
on page
8
).
7.
Remove the interconnect tray from the enclosure (
Removing the Interconnect Tray
on page
15
).
8.
Remove the enclosure from the rack (
Removing the HP PC Blade Enclosure from the Rack
on page
16
).
Non-Hot-Plug Procedures
21