HP BladeSystem c3000 HP c3000 DDR2 Onboard Administrator Installation Instruct
HP BladeSystem c3000 Manual
 |
View all HP BladeSystem c3000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP BladeSystem c3000 manual content summary:
- HP BladeSystem c3000 | HP c3000 DDR2 Onboard Administrator Installation Instruct - Page 1
HP BladeSystem Onboard Administrator User Guide. You can install the optional HP c3000 DDR2 Onboard Administrator module in the enclosure without a second module. Before you install an HP c3000 Dual Onboard Administrator in the enclosure, you must have installed the c3000 DDR2 Onboard Administrator - HP BladeSystem c3000 | HP c3000 DDR2 Onboard Administrator Installation Instruct - Page 2
Instructions or HP BladeSystem c3000 Enclosure Setup and Installation Guide for more information. Installing a c3000 Dual Onboard Administrator module 1. If necessary, remove the installed Onboard Administrator blank. 2. Slide the c3000 Dual Onboard Administrator module into the 3000 DDR2 Onboard
-
1 -
2
 |
 |
HP c3000 DDR2 Onboard
Administrator
Installation Instructions
for HP BladeSystem c3000 and c3000 Tower Enclosure
Introduction
There are two optional Onboard Administrator modules available
with the enclosure:
•
HP c3000 DDR2 Onboard Administrator module, part number
488099-B21
•
HP c3000 Dual Onboard Administrator module, part number
488100-B21
To use the Onboard Administrator modules, you must have HP
BladeSystem Onboard Administrator version 2.30 or greater
installed. For more information on using the Onboard Administrator
software, see the
HP BladeSystem Onboard Administrator User
Guide.
You can install the optional HP c3000 DDR2 Onboard Administrator
module in the enclosure without a second module.
Before you install an HP c3000 Dual Onboard Administrator in the
enclosure, you must have installed the c3000 DDR2 Onboard
Administrator module.
NOTE:
The HP BladeSystem c3000 Enclosure is shown
in the illustrations throughout this document. The HP
BladeSystem c3000 Tower Enclosure is rotated 90
degrees clockwise from what is shown in the
illustrations.
HP c3000 DDR2 Onboard
Administrator module components
Item
Name
Description
1
Insight Display
A display that
provides
information about
the health and
operation of the
enclosure
2
Serial connector
Serial RS232 DB-9
connector with PC
standard pinout.
3
UID LED
Blue = UID on
Dark = UID off
Item
Name
Description
4
Active Onboard
Administrator LED
An LED that
indicates which
Onboard
Administrator is
active
5
Health LED
Green = OK
Red = Critical error
6
USB
A USB 2.0 Type A
connector that
connects supported
USB devices
7
Reset button
—
HP c3000 Dual Onboard
Administrator module components
Item
Name
Description
1
Serial connector
Serial RS232 DB-9
connector with PC
standard pinout
2
UID LED
Blue = UID on
Dark = UID off
3
Active Onboard
Administrator LED
An LED that
indicates which
Onboard
Administrator is
active
4
Health LED
Green = OK
Red = Critical error
5
USB
USB 2.0 Type A
connector that
connects supported
USB devices
6
Reset button
—
Upgrading an HP Onboard
Administrator module to an HP
c3000 DDR2 Onboard
Administrator module
1.
Disconnect all cables from the HP Onboard Administrator
module.
2.
Remove the HP Onboard Administrator module.
3.
Slide either the c3000 Dual Onboard Administrator module (if
ordered) or an Onboard Administrator blank into the c3000
DDR2 Onboard Administrator module, and close the handle.
© Copyright 2008, 2009 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The
only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing
herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Bluetooth is a trademark owned by its proprietor and used by Hewlett-
Packard Company under license.
Part Number 488456-002
September 2009 (Second Edition)