HP Cc3310 Intel Server Management (ISM) Installation and User's Guide - Page 102

Utilities

Get HP Cc3310 - Server - AC Option PDF manuals and user guides View all HP Cc3310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

Intel Server Management (ISM) Installation and User's Guide Appendix A Utilities An option in the Server Configuration Wizard allows you to run these Server Configuration Utilities: • Service Partition Administrator (SPADMIN) • System Setup Utility (SSU) • Field Replaceable Units (FRU) and Sensor Data Record (SDR) Loader Utility Service Partition Administrator (SPADMIN) SPADMIN is the software utility that lets you create and configure the service partition on the server's hard disk drive. For information on how to use this utility, refer to the server's platform documentation. System Setup Utility The SSU lets you set and display specific attributes of the server's firmware. You should be very familiar with the configurable aspects of the server before using the SSU to alter any settings. Not only can you enter the SSU from the Server Configuration Wizard, you can also run SSU in these ways: 24. When you boot locally from the service partition you receive a DOS prompt. Enter the commands cd \ssu ssu 25. You can remotely run the SSU interface from the management station console using the Client SSU (CSSU) component of ISM. To reboot to the service partition and run SSU, Select (Re)Connect from the Server menu in CSSU. 26. You can remotely run SSU from the management station console using the Direct Platform Control (DPC) component of ISM. To reboot to the service partition and access SSU from DPC, first connect to the appropriate server, then in the Action menu select Reboot to Service Partition. In the Service Partition menu that subsequently appears, select Run Program. Then either select SSU or enter the command line SSU. FRUSDR Loader Utility The FRUSDR Load utility lets you load and display system FRUs and SDRs. For information on how to use this utility, refer to the server Product Guide. 102

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Intel Server Management (ISM) Installation and User’s Guide
Appendix A
102
Utilities
An option in the Server Configuration Wizard allows you to run these Server Configuration Utilities:
•
Service Partition Administrator (SPADMIN)
•
System Setup Utility (SSU)
•
Field Replaceable Units (FRU) and Sensor Data Record (SDR) Loader Utility
Service Partition Administrator (SPADMIN)
SPADMIN is the software utility that lets you create and configure the service partition on the server’s hard
disk drive. For information on how to use this utility, refer to the server’s platform documentation.
System Setup Utility
The SSU lets you set and display specific attributes of the server’s firmware. You should be very familiar
with the configurable aspects of the server before using the SSU to alter any settings.
Not only can you enter the SSU from the Server Configuration Wizard, you can also run SSU in these ways:
24.
When you boot locally from the service partition you receive a DOS prompt. Enter the commands
cd \ssu
ssu
25.
You can remotely run the SSU interface from the management station console using the Client SSU
(CSSU) component of ISM. To reboot to the service partition and run SSU, Select
(Re)Connect
from the
Server menu in CSSU.
26.
You can remotely run SSU from the management station console using the Direct Platform Control
(DPC) component of ISM. To reboot to the service partition and access SSU from DPC, first connect to
the appropriate server, then in the Action menu select
Reboot to Service Partition
. In the Service
Partition menu that subsequently appears, select
Run Program
. Then either select
SSU
or enter the
command line SSU.
FRUSDR Loader Utility
The FRUSDR Load utility lets you load and display system FRUs and SDRs. For information on how to use
this utility, refer to the server
Product Guide
.