HP Cisco MDS 9020 Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Rel - Page 37
Workaround, Symptom, show system reset reason, This issue is resolved.
View all HP Cisco MDS 9020 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 37 highlights
Caveats Send documentation comments to [email protected] 2) At 347955 usecs after Tue May Reason: Watchdog Timeout Service: Version: 3.2(2c) 3) At 110808 usecs after Tue May Reason: Watchdog Timeout Service: Version: 3.2(2c) 4) At 756666 usecs after Tue May Reason: Watchdog Timeout Service: Version: 3.2(2c) 6 01:18:48 2008 6 01:16:13 2008 6 01:13:39 2008 Workaround: This issue is resolved. • CSCsq17989 Symptom: During an upgrade for Release 3.1(3a) to Release 3.2(3a), the standby Supervisor modules is reset due to a global synchronization failure. The following message will be displayed: 2008 Apr 30 23:21:39 EX0-ECA-01A %SYSMGR-2-GSYNC_ABORT: Global sync aborted by signal. 2008 Apr 30 23:21:40 EX0-ECA-01A %PLATFORM-5-MOD_REMOVE: Module 5 removed (Serial number JAB091802TC) If you issue the show system reset reason command, an incorrect reason for the reset is shown. Workaround: This issue is resolved. • CSCsq25859 Symptom: A DS-X9124 module (module 1 in this case) experienced a D-cache parity error and reloaded by itself. Examples of the log messages are seen below: 2008 May 6 09:28:09 SWITCH %MODULE-4-MOD_WARNING: Module 8 (serial: JABxxxxxxxx) reported warnings on ports 8/1-8/3 (Unknown) due to BE2 Arbiter experienced an error in device 65 (device error 0xc4102613) 2008 May 6 09:28:09 SWITCH %MODULE-4-MOD_WARNING: Module 7 (serial: JABxxxxxxxx) reported warnings on ports 7/1-7/3 (Unknown) due to BE2 Arbiter experienced an error in device 65 (device error 0xc4102613) 2008 May 6 09:28:14 SWITCH %XBAR-5-XBAR_STATUS_REPORT: Module 1 reported status for component 88 code 0x40240015. 2008 May 6 09:28:14 SWITCH %MODULE-2-MOD_DIAG_FAIL: Module 1 (serial: JABxxxxxxxx) reported failure on ports 1/1-1/24 (Fibre Channel) due to Fatal runtime Arb error. (DevErr is bitmap of failed modules) in device 88 (device error 0x1) This caused several other DS-X9124 modules (slots 2-6 in this case) to reset. Examples of log messages are seen below: 2008 May 6 09:28:31 SWITCH %MODULE-5-MOD_REINIT: Re-initializing module 5 (serial: JABxxxxxxxx) 2008 May 6 09:28:31 SWITCH %MODULE-5-MOD_REINIT: Re-initializing module 6 (serial: JABxxxxxxxx) 2008 May 6 09:28:31 SWITCH %MODULE-5-MOD_REINIT: Re-initializing module 4 (serial: JABxxxxxxxx) 2008 May 6 09:28:31 SWITCH %MODULE-5-MOD_REINIT: Re-initializing module 3 (serial: JABxxxxxxxx) 2008 May 6 09:28:31 SWITCH %MODULE-5-MOD_REINIT: Re-initializing module 2 (serial: JABxxxxxxxx) This issue will change an arbiter timeout value from 5 seconds to 1.5 seconds in order to prevent other modules from resetting when one resets. OL-14116-10 Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Release 3.3(2) 37