HP Cisco MDS 9020 Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Rel - Page 17
Upgrading with IVR Enabled, Current Release with, FICON Enabled, Upgrade Path
View all HP Cisco MDS 9020 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 17 highlights
Upgrading Your Cisco MDS SAN-OS Software Image Send documentation comments to [email protected] Table 7 FICON Nondisruptive Upgrade Path to SAN-OS 3.3(3) Current Release with FICON Enabled SAN-OS 2.0(2b) SAN-OS 1.x Upgrade Path Use the interface shutdown command to administratively shut any Fibre Channel ports on Generation 1 modules that are in an operationally down state before nondisruptively upgrading from SAN-OS Release 2.0(2b) to SAN-OS Release 3.0(2) or SAN-OS Release 3.0(3b), and then upgrade to Release 3.3(1c). An operationally down state includes Link failure or not-connected, SFP not present, or Error Disabled status in the output of a show interface command. When an interface is administratively shut it will then show as Administratively down. Interfaces that are currently up or trunking do not need to be shut down. Upgrade to SAN-OS Release 3.0(2). Use the interface shutdown command to shut all the ports operationally down and administratively up on all the Generation 1 modules before nondisruptively upgrading to Release 2.0(2b) and then upgrade to 1.3(4a). Upgrading with IVR Enabled An Inter-Switch Link (ISL) flap resulting in fabric segmentation or a merge during or after an upgrade from Cisco MDS SAN-OS Release 2.0(x) to a later image where IVR is enabled might be disruptive. Some possible scenarios include the following: • FCIP connection flapping during the upgrade process resulting in fabric segmentation or merge. • ISL flap results in fabric segmentation or merge because of hardware issues or a software bug. • ISL port becomes part of PCP results in fabric segmentation or merge because of a port flap. If this problem occurs, syslogs indicate a failure and the flapped ISL could remain in a down state because of a domain overlap. This issue was resolved in Cisco SAN-OS Release 2.1(2b); you must upgrade to Release 2.1(2b) before upgrading to Release 3.3(3). An upgrade from Cisco SAN-OS Releases 2.1(1a), 2.1(1b), or 2.1(2a) to Release 2.1(2b) when IVR is enabled requires that you follow the procedure below, and then follow the upgrade guidelines listed in the "Upgrading Your Version of Cisco Fabric Manager" section on page 10. If you have VSANs in interop mode 2 or 3, you must issue an IVR refresh for those VSANs. To upgrade from Cisco SAN-OS Releases 2.1(1a), 2.1(1b), or 2.1(2a) to Release 2.1(2b) for all other VSANs with IVR enabled, follow these steps: Step 1 Configure static domains for all switches in all VSANs where IVR is enabled. Configure the static domain the same as the running domain so that there is no change in domain IDs. Make sure that all domains are unique across all of the IVR VSANs. We recommend this step as a best practice for IVR-non-NAT mode. Issue the fcdomain domain id static vsan vsan id command to configure the static domains. Note Complete Step 1 for all switches before moving to Step 2. Step 2 Issue the no ivr virtual-fcdomain-add vsan-ranges vsan-range command to disable RDI mode on all IVR enabled switches. The range of values for a VSAN ID is 1 to 4093. This can cause traffic disruption. OL-14116-11 Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Release 3.3(3) 17