Home » HP Manuals » Storage Devices » HP Cisco MDS 9134 » Manual Viewer

HP Cisco MDS 9134 Cisco MDS 9200 Series Hardware Installation Guide (OL-16188- - Page 46

LEDs on the Storage Services Module, 32-Port Fibre Channel Advanced Services Module

Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Services Modules Chapter 1 Product Overview LEDs on the Storage Services Module Table 1-9 describes the LEDs for the Cisco MDS 9000 Family Storage Services Module. Table 1-9 LEDs for the Cisco MDS 9000 Family Storage Services Module LED Status Speed Link Status Green Orange Red On Off Solid green Steady flashing green Intermittent flashing green Solid yellow Flashing yellow Off Description All diagnostics pass. The module is operational (normal initialization sequence). One of the following occurs or occurred: • The module is booting or running diagnostics (normal initialization sequence). • The inlet air temperature of the system exceeded the maximum system operating temperature limit (a minor environmental warning). To assure maximum product life, you should immediately correct the environmental temperature and restore the system to normal operation. One of the following occurs or occurred: • The diagnostic test failed. The module is not operational because a fault occurred during the initialization sequence. • The inlet air temperature of the system exceeded the safe operating temperature limits of the card (a major environmental warning). The card shut down to prevent permanent damage. 2-Gbps mode. 1-Gbps mode. Link is healthy. Link is healthy and beacon is enabled. Link is up and traffic is flowing through port. Link is disabled by software. A fault condition exists. No link. 32-Port Fibre Channel Advanced Services Module The Cisco MDS 9000 Family 32-port Fibre Channel Advanced Services Module (ASM) enables pooling of heterogeneous storage for increased storage utilization, simplified storage management, and reduced total cost of storage ownership. The ASM incorporates all the capabilities of the Cisco MDS 9000 DS-X9032 Fibre Channel switching module and also provides scalable, in-band storage virtualization services. The ASM module makes it possible to allocate bandwidth optimally. 1-28 Cisco MDS 9200 Series Hardware Installation Guide OL-16188-01

Section	Page
Cisco MDS 9200 Series Hardware Installation Guide	1
Contents	3
New and Changed Information	9
Preface	13
Related Documentation	16
Release Notes	16
Compatibility Information	16
Regulatory Compliance and Safety Information	16
Hardware Installation	16
Cisco Fabric Manager	16
Command-Line Interface	17
Intelligent Storage Networking Services Configuration Guides	17
Troubleshooting and Reference	17
Installation and Configuration Note	17
Obtaining Documentation, Obtaining Support, and Security Guidelines	18
Product Overview	19
Chassis	20
Cisco MDS Fibre Channel Bladeswitch for IBM Blade Center	23
Integrated Supervisor Modules	23
Cisco MDS 9222i Integrated Supervisor Module	24
Cisco MDS 9216i Integrated Supervisor Module	24
Cisco MDS 9216A Integrated Supervisor Module	25
LEDs on the Cisco MDS 9200 Series Integrated Supervisor Modules	27
Interface Modules	28
LEDs on the Interface Module	29
Cisco MDS 9000 Family Module Compatibility	30
Switching Modules	30
48-Port 4-Gbps Fibre Channel Switching Module	31
24-port 4-Gbps Fibre Channel Switching Module	32
12-port 4-Gbps Fibre Channel Switching Module	32
4-port 10-Gbps Fibre Channel Switching Module	33
LEDs on the Generation 2 Switching Modules	34
32-Port 2-Gbps Fibre Channel Switching Module	34
16-Port 2-Gbps Fibre Channel Switching Module	35
Switching Module Features	36
LEDs on the Generation 1 Switching Module	37
Services Modules	38
1 8/4-Port Multiservice Module	38
18/4-Port Multiservice Federal Information Processing Standards Module	39
LEDs on the 18/4-Port Multiservice Module	40
14/2-Port Multiprotocol Services Module	40
LEDs on the 14/2-Port Multiprotocol Services Module	42
IP Storage Services Modules	42
LEDs on IP Storage Services Module	44
32-Port Fibre Channel Storage Services Module	44
LEDs on the Storage Services Module	46
32-Port Fibre Channel Advanced Services Module	46
LEDs on the Fibre Channel Advanced Services Module	48
Caching Services Module	48
LEDs on the Caching Services Module	51
Power Supplies	52
Fan Module	53
Supported Transceivers	53
X2 Fibre Channel Transceivers	54
Fibre Channel SFP Transceivers	54
Combination Fibre Channel/Gigabit Ethernet SFP Transceivers	54
CWDM Combination Fibre Channel/Gigabit Ethernet SFP Transceivers	55
Gigabit Ethernet SFP Transceivers	55
DWDM Fibre Channel SFP Transceivers	55
Installing the Cisco MDS 9200 Series	57
Preinstallation	58
Installation Options	58
Installation Guidelines	59
Required Equipment	60
Unpacking and Inspecting the Switch	60
Installing the Chassis in a Cabinet or Rack	61
Installing the Switch in a Cabinet with Insufficient Front Clearance	67
Installing Front Rack-Mount Brackets for Cabinets with 26 Inches or Greater of Rail Spacings	68
Installing Front Rack-Mount Brackets for Cabinets with Less Than 26 Inches of Rail Spacings	70
Installing the Cisco MDS 9200 Series Rear-Facing into Cabinet	72
System Grounding	75
Proper Grounding Practices	75
Preventing Electrostatic Discharge Damage	77
Establishing the System Ground	79
Required Tools and Equipment	79
Grounding the Chassis	80
Starting Up the Switch	82
Removing and Installing Components	84
Removing and Installing Switching and Services Modules	84
Removing a Caching Services Module	87
Removing Other Switching or Services Modules	88
Installing a Switching or Services Module, Including Caching Services Modules	89
Verifying Installation of a Switching or Services Module	90
Maintaining a Caching Services Module	91
Maintaining the Batteries on the Caching Services Module	91
Maintaining the Disk Drives on the Caching Services Module	91
Removing and Installing Power Supplies	92
Removing a Power Supply	92
Installing a Power Supply	92
Removing and Installing the Fan Module	94
Removing a Fan Module	95
Installing a Fan Module	95
Removing the Cisco MDS 9200 Series	96
Connecting the Cisco MDS 9200 Series	97
Preparing for Network Connections	98
Connecting to the Console Port	98
Connecting to the COM1 Port	100
Connecting to the MGMT 10/100 Ethernet Port	101
Connecting to a Fibre Channel Port	102
Removing and Installing X2 Transceivers	102
Installing an X2 Transceiver	104
Removing an X2 Transceiver	104
Removing and Installing SFP Transceivers	104
Installing an SFP Transceiver	105
Removing an SFP Transceiver	106
Removing and Installing Cables into SFP Transceivers	107
Installing a Cable into an SFP Transceiver	107
Removing a Cable from an SFP Transceiver	108
Maintaining SFP Transceivers and Fiber-Optic Cables	109
Cabinet and Rack Installation	111
Cabinet and Rack Requirements	111
General Requirements for Cabinets and Racks	111
Requirements Specific to Perforated Cabinets	112
Requirements Specific to Solid-Walled Cabinets	113
Requirements Specific to Standard Open Racks	113
Requirements Specific to telco Racks	113
Cisco MDS 9000 Family telco and EIA Shelf Bracket	114
Rack-Mounting Guidelines	114
Before Installing the Shelf Brackets	115
Required Equipment	115
Installing the Shelf Bracket Kit into a Two-Post telco Rack	116
Installing the Shelf Bracket Kit into a Four-Post EIA Rack	117
Installing the Switch on the Shelf Brackets	118
Removing the Shelf Bracket Kit (Optional)	119
Technical Specifications	121
Switch Specifications	121
Module Specifications	122
Weight of Modules	123
Power Specifications	124
Specifications for the Cisco MDS 9200 Series Power Supplies	124
Component Power Requirements and Heat Dissipation Specifications	125
X2 Transceiver Specifications	126
Cisco 10-Gbps Fibre Channel X2 Transceivers	127
General Specification for Cisco 10-Gbps Fibre Channel X2 Transceivers	127
Environmental Conditions and Power Requirement Specifications for Cisco 10-Gbps Fibre Channel X2 Transceivers	127
Cisco 10-Gbps Ethernet X2 Transceivers	128
General Specification for Cisco 10-Gbps Ethernet X2 Transceivers	128
Environmental and Power Requirements Specifications for Cisco 10-Gbps Ethernet X2 Transceiver	129
SFP Transceiver Specifications	129
Cisco Fibre Channel SFP Transceivers	130
General Specifications for Cisco 4-Gbps Fibre Channel SFP Transceivers	130
Environmental and Power Requirement for Cisco 4-Gbps Fibre Channel SFP Transceivers	131
General Specifications for Cisco 2-Gbps Fibre Channel SFP Transceivers	132
Environmental and Power Requirement for Cisco 2-Gbps Fibre Channel SFP Transceivers	132
Maximum Environmental and Electrical Ratings for Cisco Fibre Channel SFP Transceivers	133
Cisco Fibre Channel/Gigabit Ethernet Transceivers	133
General Specifications for Cisco Fibre Channel/Gigabit Ethernet SFP Transceivers	134
Environmental and Power Requirement Specifications for Cisco Fibre Channel/Gigabit Ethernet SFP Transceivers	134
Cisco CWDM SFP Transceivers	135
Environmental and Optical Specifications for Cisco 2-Gbps CWDM SFP Transceivers	136
Environmental and Optical Specifications for Cisco 4-Gbps CWDM SFP Transceivers	138
Cisco Gigabit Ethernet Transceivers	139
General Specifications for Cisco Gigabit Ethernet Transceivers	139
Environmental and Power Requirement Specifications for Cisco Gigabit Ethernet Transceivers	139
DWDM Fibre Channel SFP Transceivers	140
Cable and Port Specifications	143
Cables and Adapters Provided	143
Console Port	144
Console Port Pinouts	144
Connecting the Console Port to a Computer Using the DB-25 Adapter	144
Connecting the Console Port to a Computer Using the DB-9 Adapter	145
COM1 Port	145
COM1 Port Pinouts	146
Connecting the COM1 Port to a Modem	146
MGMT 10/100/1000 Ethernet Port	147
MGMT 10/100 Ethernet Port	148
Supported Power Cords and Plugs	150
Power Cords	150
Supported Plugs for 6000-W AC, 2500-W AC, and 1900-W AC Power Supplies	151
Supported Plugs for the 4000-W AC Power Supply	153
Jumper Power Cord	153
Site Planning and Maintenance Records	155
Site Preparation Checklist	155
Contact and Site Information	157
Chassis and Module Information	158