HP D2D2503i HP StoreOnce 2700, 4500 and 4700 Backup system Maintenance and Ser - Page 17

Replacing the system motherboard, Motherboard spares part numbers

Get HP D2D2503i PDF manuals and user guides View all HP D2D2503i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

4 Replacing the system motherboard For all products, refer to the appropriate Maintenance and Server Guide for detailed instructions on replacing the motherboard. This chapter describes the following tasks that are specific to HP StoreOnce Backup Systems: • Update BIOS IDs on all products. • Reinstate iLO4 licences on all products • Run the StoreOnce CLI command, hardware show firmware, to check that the firmware on the new motherboard is correct and run the StoreOnce CLI command, hardware update firmware with appropriate parameters to update it, if necessary. IMPORTANT: When replacing the motherboard (or individual cards) be sure to always replace cards into the same slot from which they were removed. See also the rear view drawings in Chapter 2. Motherboard spares part numbers The motherboard for the HP StoreOnce 4700 and 4500 Backup is the standard DL380p G8 motherboard, spares part number 662530-001. Please refer to the DL380p G8 Maintenance and Service Guide for details of how to replace it. The motherboard for the HP StoreOnce 2700 Backup is the standard DL360p G8 motherboard, spares part number 718781-001. Please refer to the DL360p G8 Maintenance and Service Guide for details of how to replace it. Before replacing the motherboard- a note about licenses iLO4 licenses All products are shipped with paper copies of the iLO4 licenses. If you no longer have these licenses and the board is still working for the iLO4 GUI connection via its management Ethernet port, make a note of the license before you remove the motherboard. (If it is not working, contact HP Support.) 1. Log on to the iLO4 GUI. 2. Select the Administration Tab. 3. Select Licensing and make a note of the Activation Key. After replacing the motherboard (all products) For all products you must: 1. Boot the system. During the system BIOS boot process, when the prompt to Press F9 is visible, press the F9 key to enter the RBSU (ROM-based Setup Utility) or BIOS Setup. This is so that you can change settings. 2. Change the RBSU settings, as shown in the following table. NOTE: Unless noted otherwise, the settings apply to all products. Motherboard spares part numbers 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
4 Replacing the system motherboard
For all products, refer to the appropriate Maintenance and Server Guide for detailed instructions
on replacing the motherboard. This chapter describes the following tasks that are specific to HP
StoreOnce Backup Systems:
•
Update BIOS IDs on all products.
•
Reinstate iLO4 licences on all products
•
Run the StoreOnce CLI command,
hardware show firmware
, to check that the firmware
on the new motherboard is correct and run the StoreOnce CLI command,
hardware update
firmware
with appropriate parameters to update it, if necessary.
IMPORTANT:
When replacing the motherboard (or individual cards) be sure to always replace
cards into the same slot from which they were removed. See also the rear view drawings in Chapter
2.
Motherboard spares part numbers
The motherboard for the HP StoreOnce 4700 and 4500 Backup is the standard DL380p G8
motherboard, spares part number 662530–001. Please refer to the
DL380p G8 Maintenance
and Service Guide
for details of how to replace it.
The motherboard for the HP StoreOnce 2700 Backup is the standard DL360p G8 motherboard,
spares part number 718781–001. Please refer to the
DL360p G8 Maintenance and Service Guide
for details of how to replace it.
Before replacing the motherboard— a note about licenses
iLO4 licenses
All products are shipped with paper copies of the iLO4 licenses. If you no longer have these licenses
and the board is still working for the iLO4 GUI connection via its management Ethernet port, make
a note of the license before you remove the motherboard. (If it is not working, contact HP Support.)
1.
Log on to the iLO4 GUI.
2.
Select the
Administration
Tab.
3.
Select
Licensing
and make a note of the Activation Key.
After replacing the motherboard (all products)
For all products you must:
1.
Boot the system. During the system BIOS boot process, when the prompt to Press F9 is visible,
press the F9 key to enter the RBSU (ROM-based Setup Utility) or BIOS Setup. This is so that
you can change settings.
2.
Change the RBSU settings, as shown in the following table.
NOTE:
Unless noted otherwise, the settings apply to all products.
Motherboard spares part numbers
17