HP E24i User Guide - Page 28

Button lockouts, Using the auto-adjustment function (analog input), Image, Auto Adjustment

Get HP E24i PDF manuals and user guides View all HP E24i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Button lockouts Holding down the power button or Menu button for 10 seconds disables that button. You can re-enable the button by holding the button down again for 10 seconds. The button lockout function is available only when the monitor is on, an active signal is displayed, and the OSD menu is closed. Using the auto-adjustment function (analog input) The auto-adjustment feature automatically engages and attempts to optimize your screen under the following conditions: ● Monitor setup ● Factory reset of the computer ● Changing monitor resolution You can manually optimize the screen performance for the VGA (analog) input at any time from the Auto Adjustment menu in the OSD. You can download the auto-adjustment pattern software utility from http://www.hp.com/support. Do not use this procedure if the monitor is using an input other than VGA. If the monitor is using a VGA (analog) input, this procedure can correct the following image quality conditions: ● Fuzzy or unclear focus ● Ghosting, streaking, or shadowing effects ● Faint vertical bars ● Thin, horizontal scrolling lines ● An off-center picture To use the auto-adjustment feature: 1. Turn the monitor on, and then wait for 20 minutes before adjusting. 2. Press the Menu button to open the OSD menu, select Image, and then select Auto Adjustment. If the result is not satisfactory, continue with the procedure. 3. Open the auto-adjustment utility. (You can download this utility from http://www.hp.com/support.) The setup test pattern is displayed. 4. Press the Esc key or any other key on the keyboard to exit the test pattern. 22 Chapter 3 Support and troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
Button lockouts
Holding down the power button or
Menu
button for 10 seconds disables that button. You can re-enable the
button by holding the button down again for 10 seconds. The button lockout function is available only when
the monitor is on, an active signal is displayed, and the OSD menu is closed.
Using the auto-adjustment function (analog input)
The auto-adjustment feature automatically engages and attempts to optimize your screen under the
following conditions:
●
Monitor setup
●
Factory reset of the computer
●
Changing monitor resolution
You can manually optimize the screen performance for the VGA (analog) input at any time from the Auto
Adjustment menu in the OSD. You can download the auto-adjustment pattern software utility from
support
.
Do not use this procedure if the monitor is using an input other than VGA. If the monitor is using a VGA
(analog) input, this procedure can correct the following image quality conditions:
●
Fuzzy or unclear focus
●
Ghosting, streaking, or shadowing effects
●
Faint vertical bars
●
Thin, horizontal scrolling lines
●
An off-center picture
To use the auto-adjustment feature:
1.
Turn the monitor on, and then wait for 20 minutes before adjusting.
2.
Press the
Menu
button to open the OSD menu, select
Image
, and then select
Auto Adjustment
. If the
result is not satisfactory, continue with the procedure.
3.
Open the auto-adjustment utility. (You can download this utility from
support
.) The
setup test pattern is displayed.
4.
Press the
Esc
key or any other key on the keyboard to exit the test pattern.
22
Chapter 3
Support and troubleshooting