HP Elite 7200 Illustrated Parts & Service Map HP Elite 7200 Series Microto - Page 3

Setup Utility Basic system information is in the Setup Utility held in the system ROM, accessed by pressing F10 when prompted (on screen) during the boot sequence. Computer Setup Menu Heading Option / Description Main System Time Allows you to set system time. System Date Allows you to set system date. Language Allows you to select the language. 1st Drive 2nd Drive 3rd Drive 4th Drive Allow you to: view capacity (HDD only). Also allows you to run HDD self-test for selected channel: SMART status check, SMART short self test, SMART extended self test. System Information Allows you to view installed memory, memory banks 14, BIOS revision, core version. Model Number Allows you to modify the model number. Serial Number Allows you to manually enter the serial number. Asset Tag Allows you to manually enter the Asset Tag. Product Number View only. Allows you to view the product number. Advanced CPU Type View only. CPU Speed View only. Cache RAM(L2) View only. Cache RAM(L3) View only. Primary Video Adapter Allows you to select boot display device when more than 2 video options are offered by system: PCIe x1 and PCIe x16. SATA Controller Mode If SATA controller is enabled, allows you to set the mode to: IDE, AHCI, RAID. SATA Controller Allows you to disable/enable the SATA controller. Onboard LAN Disable/enable onboard LAN controller. Onboard LAN Boot Disable/enable the boot ROM of the onboard LAN chip. ROM USB Ports Allows you to individually enable/disable available USB ports. Onboard 1394 Allows you to enable/disable all 1394 ports. Supervisor Password Allows you to view the supervisor password. User Password Allows you to view the user password. Onboard Audio Auto/disable/enable. ESC: Boot Menu Allows you to enable/disable the option to press the Esc key to access the Boot menu during computer startup. F9:Diagnostics Allows you to enable/disable the option to press the F9 key to access the Diagnostics menu during computer startup. F10:Setup Allows you to enable/disable the option to press the F10 key to access the Setup menu during computer startup. F11:Recovery Allows you to enable/disable the option to press the F11 key to access the Recovery menu during computer startup. F12:Boot from LAN Allows you to enable/disable the option to press the F12 key to access the Boot from LAN option during computer startup. Power After AC Power Fail- Allows you to select system restart behavior after power ure loss: Stay off, Power on, Auto. Hyper-threading Disable/enable. XD (Execute Disable) Disable/enable XD bit. Virtualization Tech- Disable/enable. nology WOL from S5 Allows you to enable/disable Limited (normal shutdown) WOL from S5 support. Boot Boot-time Diagnostic Disable/enable POST diagnostic messages display. Screen Boot Device Priority: 1st Boot Device, 2nd Boot Device, 3rd Boot Device, 4th Boot Device Allows you to specify which device groups will boot first, second, third, and fourth or to disable any of the four: Floppy group, CD-ROM group, Hard drive group, Network boot group. MS-DOS drive lettering assignments maybe apply after a non-MS-DOS operating system has started. Floppy Group Boot Specifies boot device priority within removable devices. Priority CD-ROM Boot Prior- Specifies boot device priority within CD/DVD drives. ity Hard Drive Boot Pri- Specifies boot device priority within hard drives. ority Network Group Boot Specifies boot device priority within bootable network Priority devices. Exit Exit Saving Changes Press Enter to exit saving changes. Exit Discarding Changes Press Enter to exit discarding changes. Load Setup Defaults Press Enter to load setup defaults. Discard Changes Press Enter to discard changes. Save Changes Press Enter to save changes. Recovering the Configuration Settings To reset all BIOS Setup options to their default values (including options for Ctrl+F10), you must enter F10 Setup mode and press F5. This does not include updates to system date, system time, supervisor password, user password, and CPU frequency multiplier. Password Security This computer supports security password features, which can be established through the Computer Setup Utilities menu. This computer supports two security password features that are established through the Computer Setup Utilities menu: setup password and power-on password. When you establish only a setup password, any user can access all the information on the computer except Computer Setup. When you establish only a power-on password, the power-on password is required to access Computer Setup and any other information on the computer. When you establish both passwords, only the setup password will give you access to Computer Setup. When both passwords are set, the setup password can also be used in place of the power-on password as an override to log in to the computer. This is a useful feature for a network administrator. If you forget the password for the computer, you can clear that password so you can gain access to the information on the computer by resetting the password jumper. Resetting the password jumper 1. Shut down the computer. With the power cord disconnected, press the power button again to drain the system of any residual power. 2. Remove the access panel. 3. Locate the header and jumper labeled JPD1. 4. Remove the jumper from pins 1 and 2. Place the jumper on pins 2 and 3. 5. Replace the access panel. 6. Plug in and turn on power. Allow the operating system to start. This clears the current passwords and disables the password features. 7. To establish new passwords, repeat steps 1 - 4, replace the password jumper on pins 1 and 2, then repeat steps 5 - 6. Establish new passwords in Computer Setup. Resetting the CMOS jumper The CMOS button resets CMOS but does not clear the power-on and setup passwords. 1. Turn off the computer and any external devices, and disconnect power. 2. Remove the access panel. 3. Locate the header and jumper labeled JBAT1. 4. Remove the CMOS jumper from pins 1 and 2 and put the jumper on pins 2 and 3. This clears the CMOS. 5. Put the jumper back on pins 1 and 2. 6. Replace the access panel, external devices, and reconnect the power cord. 7. Turn on the computer. Use Computer Setup to reset any special system setups along with the date and time. HP Vision Diagnostics The Hewlett-Packard Vision Diagnostics utility allows you to view information about the hardware configuration of the computer and perform hardware diagnostic tests on the subsystems of the computer. The utility simplifies the process of effectively identifying, diagnosing, and isolating hardware issues. The Survey tab is displayed when you invoke HP Vision Diagnostics. This tab shows the current configuration of the computer. From the Survey tab, there is access to several categories of information about the computer. Other tabs provide additional information, including diagnostic test options and test results. The information in each screen of the utility can be saved as an html file and stored on a USB flash drive. Use HP Vision Diagnostics to determine if all the devices installed on the computer are recognized by the system and functioning properly. Running tests is optional but recommended after installing or connecting a new device. Vision Diagnostics may be found on the CD that shipped with some computer models. The tool may also be downloaded from the HP Web site using the following procedure: 1. Go to www.hp.com 2. Click the Software & Drivers link. 3. Select Download drivers and software (and firmware). 4. Enter the product number in the text box and press Enter. 5. Select the specific product. 6. Select the OS. 7. Click the Diagnostic link. 8. Click Hewlett-Packard Vision Diagnostics. 9. Click Download. NOTE: The download includes instructions on how to create a bootable CD or USB flash drive. POST Front Panel LEDs and Audible Codes Beeps/ Activity Meaning Recommended Action 1 short, 1 long, Bad memory or memory 3 sec pause configuration error. Check that the memory modules have been installed correctly and that proper modules are used. 2 short, 1 long, No graphics card installed 3 sec pause or graphics card initializa- tion failed. For systems with a graphics card: 1. Reseat graphics card. Power on system. 2. Replace the graphics card. 3. Replace the system board. For systems with integrated graphics, replace the system board. 3 short, 1 long, 3 sec pause CPU configuration error or invalid CPU detected before graphics card initialized. 1. Upgrade the BIOS to proper version. 2. Change the processor. 1 short, 1 sec pause No optical drive found. 1. Check cable connections. 2. Run the Computer Setup utility and ensure the device port is enabled. 2 short, 1 sec pause No CD found. 1. Check the type of drive and use the correct media type. 2. Replace the CD with a new one. 3 short, 1 sec pause Flashing not ready (miss- Upgrade the BIOS to proper version. ing utility or BIOS image file, etc.) 4 short, 1 sec pause Flashing operation has failed (checksum error, corrupted image, etc.) 1. Verify the correct ROM. 2. Flash the ROM if needed. 3. If an expansion board recently added, remove to see if the problem remains. 4. Clear CMOS. 5. If the message disappears, there may be a problem with the expansion card. 6. Replace the system board. 5 short, 1 sec pause BIOS recovery was suc- No action required. cessful. HP Elite 7200 MT Series 640041-001 page 3