HP Elite Folio 13.5 Maintenance and Service Guide - Page 52

Antenna bar, Disconnect the antenna cables from the WWAN module

Get HP Elite Folio 13.5 PDF manuals and user guides View all HP Elite Folio 13.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

2. Peel the cable off the computer (2). The cable is secured to the computer with adhesive. Reverse this procedure to install the POGO connector. Antenna bar To remove and disassemble the antenna bar, use these procedures and illustrations. Table 6-10 Antenna bar description and part number Description Antenna bar (main) Antenna bar (aux) Spare part number M35272-001 M35273-001 Before removing the antenna bar, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 28). 2. Remove the bottom cover (see Bottom cover on page 30). 3. Disconnect the battery cable from the system board (see Battery on page 31). 4. Disconnect the display cable and the sensor cable (see Display assembly on page 46). 5. Remove the heat sink (see Heat sink on page 36). Remove the antenna bar: 1. Disconnect the antenna cables from the WWAN module (1) and the integrated WLAN module (2). 2. Remove the five reusable rubber screw covers from the antenna bar (3). 3. Remove the five Phillips M2.0 × 3.0 screws (4) that secure the antenna bar to the computer. NOTE: Three of the screws are removed vertically. Two of the screws are removed horizontally. 44 Chapter 6 Removal and replacement procedures for authorized service provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
2.
Peel the cable off the computer
(2)
. The cable is secured to the computer with adhesive.
Reverse this procedure to install the POGO connector.
Antenna bar
To remove and disassemble the antenna bar, use these procedures and illustrations.
Table 6-10
Antenna bar description and part number
Description
Spare part number
Antenna bar (main)
M35272-001
Antenna bar (aux)
M35273-001
Before removing the antenna bar, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
28
).
2.
Remove the bottom cover (see
Bottom cover
on page
30
).
3.
Disconnect the battery cable from the system board (see
Battery
on page
31
).
4.
Disconnect the display cable and the sensor cable (see
Display assembly
on page
46
).
5.
Remove the heat sink (see
Heat sink
on page
36
).
Remove the antenna bar:
1.
Disconnect the antenna cables from the WWAN module
(1)
and the integrated WLAN module
(2)
.
2.
Remove the five reusable rubber screw covers from the antenna bar
(3)
.
3.
Remove the five Phillips M2.0 × 3.0 screws
(4)
that secure the antenna bar to the computer.
NOTE:
Three of the screws are removed vertically. Two of the screws are removed horizontally.
44
Chapter 6
Removal and replacement procedures for authorized service provider parts