HP Engage Flex Pro-C G2 Maintenance and Service Guide - Page 48

Power supply, Removal and replacement procedures

Get HP Engage Flex Pro-C G2 PDF manuals and user guides View all HP Engage Flex Pro-C G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

To install the audio board, reverse the removal procedure. Power supply To remove the power supply, use these procedures. Before removing the power supply, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 18). 2. Remove the access panel (see Access panel on page 19). 3. Rotate the drive cage to the upright position (see Hard drive on page 21). Remove the power supply: 1. Disconnect the power supply cables from the following system board connectors: PWR (1) PWRCMD (2) PWRCPU (3) 2. Remove the three Torx screws (1) from the back of the computer. 3. Press the release button (2) at the front of the power supply. 42 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
To install the audio board, reverse the removal procedure.
Power supply
To remove the power supply, use these procedures.
Before removing the power supply, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
18
).
2.
Remove the access panel (see
Access panel
on page
19
).
3.
Rotate the drive cage to the upright position (see
Hard drive
on page
21
).
Remove the power supply:
1.
Disconnect the power supply cables from the following system board connectors:
PWR
(1)
PWRCMD
(2)
PWRCPU
(3)
2.
Remove the three Torx screws
(1)
from the back of the computer.
3.
Press the release button
(2)
at the front of the power supply.
42
Chapter 4
Removal and replacement procedures